Votes - 5, Average rating: 3.6
(
)
)
|
manual abstract
The display unit will be held in place by gravity; there will be no audible ‘snap’ that indicates a mechanical lock. Note: If you do not need to rotate the Cintiq pen display, you may want to secure it to the stand with the rotation lock screws. For information on this, see Optional display configurations on page 56. To learn about other mounting options, see Using an alternate mount or stand on page 57. Bearing hub Bearing recess – A – Unpacking your Cintiq Page 9 WARNING When operating the incline adjustment levers, Cintiq must be mounted on the stand with the stand feet resting on a stable, flat surface. The stand is spring-loaded and can snap back quickly, causing injury or damage if not operated properly. After the display unit has been mounted on the stand, remove the foam blocks that lock the adjustment levers in place. Save these blocks with the other packaging materials; you will need them if in the future you want to ship Cintiq. – B – Adjusting the display incline To adjust the display incline, face the front of the Cintiq pen display and grasp it on the left and right side at approximately the same height as the Cintiq stand adjustment levers. Use your fingertips to gently pull the incline adjustment levers toward the display unit; this will release the stand’s clutch mechanism. Tilt the display to adjust the incline setting. • To lower Cintiq, pull the left incline adjustment lever toward Cintiq and gently lower Cintiq to the desired incline angle. Release the lever to lock the stand in place. • To raise Cintiq, pull the right incline adjustment lever toward Cintiq and gently raise Cintiq to the desired incline angle. Release the lever to lock the stand in place. Note: The stand adjustment levers exhibit some natural play before the clutch mechanism engages. When adjusting the stand incline, set it slightly higher than you plan to work with, then lower the display to the desired position. WARNING Before moving Cintiq, first adjust the stand to its full upright position; this will reduce the spring tension so that the stand will not accidentally release and snap shut. If the display unit is in landscape orientation, use one hand to grasp the bottom of the display and with your other hand grasp the back of the stand. Be sure to lift on both the display and the stand so that the stand will not separate from the display when moving Cintiq. If Cintiq is in portrait orientation or has been locked to the stand with the rotation lock screws (see page 56), the stand will not separate from the display unit and Cintiq can be safely lifted by grasping the display unit with both hands. Unpacking your Cintiq Page 10 Adjusting rotation The pen display can be rotated on the display stand when the incline is less than or equal to 25 degrees. To adjust rotation, grasp Cintiq by the main body and rotate the unit to the desired position; it will move on the bearing hub. You can only rotate the display unit 180 degrees in either direction. If you do not plan to rotate the Cintiq, use the rotation lock screws to fasten the display to the stand in a horizontal position. See Optional display configurations on page 56 for more information. Using the pen holder The integrated pen holder is located at the back of the pen display tablet. Note: The pen holder is not available for use when routing the cable to exit through the top cable opening. Next step: Go to page 13 and familiarize yourself with the pen display. Unpacking your Cintiq Page 11 Removing Cintiq from the display stand To remove Cintiq from the display stand: • If the rotation lock screws are attached, remove them from the back of Cintiq. • Position the pen display to landscape orientation before removing it from the display stand. The stand will not release unless Cintiq is in landscape orientation. • Next, raise the stand incline to the highest position. See Adjusting the display incline on page 10 for instructions. • Firmly grasp the pen display on both the left and right sides of the body, and lift the unit out of the display stand. Important: When removing Cintiq from the display stand, always lift Cintiq in a direction parallel to the front of the stand. You may also need to rotate Cintiq slightly so the stand will release. Note: When packing Cintiq for transport, first adjust the stand to its lowest position and place the foam packing blocks under the incline adjustment levers before removing Cintiq from the stand. The foam blocks will keep the stand from snapping shut while in its packaging. Always pack Cintiq and its stand in their original containers and protective cushions. Never pack Cintiq while it is mounted on the stand; this may damage the unit or stand during transportation. Unpacking your Cintiq Page 12 CINTIQ PEN DISPLAY COMPONENTS After the Cintiq pen display is safely mounted on the Cintiq stand, take some time to familiarize yourself with its features and components. The LCD monitor and tablet sensor function as an integrated input and ...
Other models in this manual:Mouses and Keyboards - Cintiq DTZ-2000W (1.63 mb)