Votes - 0, Average rating: 0
(
)
)
|
Other manuals for this model:
manual abstract
Table 4 Validation tests (standalone system) (continued)
3.
You can deploy the product as a standalone system,
3.
Connect a power cable to the storage system.
3.
After installation completes and the server (or servers
or use multiple systems to deploy a Windows
if deploying a cluster) reboots, you are
Successful?
4.
Locate the iLO Network Settings tag attached
Test
Command(s) to execute
(Y/N)
failover cluster. If you are setting up a cluster
to the storage system and record the default
automatically logged on as the local administrator
configuration, you must connect a cable between
user name, password, and DNS name.
(using the default Windows Administrator password
another system on
the servers to complete the initial setup. Connect a
of HPinvent!). If you are deploying a cluster,
the same network.
5.
From a remote computer, open a standard
cable between the ports identified as callout 1 in
Web browser and enter the iLO management
continue to work only with the server on which you
Ping the name of
ping
Figure 1, which enables you to create a simplified
hostname of the storage system.
used the Setup Windows Wizard.
some other system
ping
two-node cluster later in the HP Initial Configuration
on the same
The HP Initial Configuration Tasks (ICT) window launches
network form the
Tasks (ICT) window. If more than two nodes are
NOTE:
By default, iLO obtains the
automatically at logon. The tasks presented vary
StoreEasy system.
desired in the cluster, create the two–node cluster
management IP address and subnet
depending on whether you have chosen to deploy a
first, then add nodes later.
mask from your network’s DHCP server.
If you will be adding the StoreEasy system to an Active Directory
standalone system or a cluster. For more information on
The hostname found on the iLO tag is
domain, some additional tests include:
any of these tasks, click the help icon for the appropriate
Figure 1 Connecting the servers
automatically registered with your
task group in the ICT window.
Ping the domain
ping
controller from the
address>
IMPORTANT:
HP strongly recommends that you
StoreEasy system.
ping
Using the default user information provided on
validate your configuration when using clusters.
name>
the iLO Network Settings tag, log on to iLO,
Whether you create a cluster through the ICT or
Verify the network
and then launch a remote console to the
pingpath
path to the domain controller address>
storage system.
is validating your configuration using the Microsoft
controller and DNS pingpath
servers is correct.
For detailed instructions about using each of these access
controller name>
methods, see the HP StoreEasy 3000 Storage
validation step, you can still validate the cluster
pingpath
after it is created.
address> (Repeat for each DNS
you can search for (by product name) at:
server)
pingpath
name> (Repeat for each DNS
Regulatory information
server)
Access the storage system
Use either the direct attach or remote management
For important safety, environmental, and regulatory
Additionally, verify that the DNS information is valid for
method to connect to the storage system.
Power on and complete the configuration
information, see Safety and Compliance Information for
the cluster and file server. HP recommends that you also
1.
Power on the system by pushing the power button
Server, Storage, Power, Networking, and Rack Products,
verify the iLO IP address and name resolution; however,
IMPORTANT:
Only the direct attach and remote
on the front panel. If using iLO, click Momentary
available at http://www.hp.com/support/
this is not critical to support the cluster and file server.
management access methods can be used to
Press under the Power Switch menu of the remote
Safety-Compliance-EnterpriseProducts.
install the storage system. After the storage system
console.
installation process is complete and the server’s
IP addresses have been assigned, you can then
IMPORTANT:
If you are deploying a
Install the storage system hardware
additionally use the remote desktop method to
cluster, only interact with one of the servers.
Documentation feedback
1.
Install the rail kit by following the HP Rack Rail Kit
access the storage system.
After powering on both servers, the Setup
Send any errors, suggestions, or comments to
Installation Instructions, which is packaged with the
Windows Wizard and the Initial
Documentation Feedback (docsfeedback@hp.com).
rail kit.
•
Direct attach —This access method is mandatory if
Configuration Tasks must be run from only
your network does not have a Dynamic Host
2.
Install the storage system into the rack.
one server.
Configuration Protocol (DHCP) server. Connect the
following cables to the back panel of the storage
The storage system starts and displays the Setup
system in the following sequence: keyboard, mouse,
Windows wizard, in which you select language
network cables, monitor cable, and power cable.
and regional settings and accept the license
agreement.
NOTE:
The keyboard, mouse, and monitor
2.
After completing the wizard, you are asked if you
are not provided with the storage system.
want to configure a standalone system or a
•
Remote management—Access the storage system
two-node cluster. Click Yes to configure your system
using the Integrated Lights-Out (iLO) remote
as a cluster or click No to configure your system as
management method:
a standalone server. The storage system installation
process takes approximately 10–15 minutes.
1.
Connect the desired network cables to network
adapter ports on the back of the storage
system.
2.
Connect a network cable to the iLO port
located on the back of the storage system.
Page 2
...
Media Storage - HP StoreEasy 3830 Gateway Storage/S-Buy (179.14 kb)
Media Storage - HP StoreEasy 3840 Gateway Storage (179.14 kb)
Media Storage - HP StoreEasy 3840 Gateway Storage/S-Buy (179.14 kb)
Media Storage - HP X3400 G2 Network Storage Gateway (179.14 kb)