Login:
Sorted: Name ↓   Downloads   Rate   Size ↑  
downloaded: 1   File size: 3 mb   Manafacture: Eureka! s  
Category: Camping Equipment
@name

2 front fig.3 fig.4 fig.5 fig.6 fig.7 fig.8 fig.9 fig.10 A E E F F C B D Component List: 1 Tent Body, 1 Tent Fly, 2 Front Poles, 2 Rear Poles , 1 Spanner, 1 Center Hoop, 2 Junction Tubes, 1 Carry Bag, 1 Pole Bag, 1 Stake Bag w/ Stakes • Unroll and unfold the tent with the floor on the ground. Remove the fly and set it aside. Do not stake the tent down yet. In windy conditions, we recommend that an end should face into the wind and that you stake down one corner of this end. See fig.1. • Join the

downloaded: 0   File size: 3 mb   Manafacture: Eureka! s  
Category: Camping Equipment
@name

These are specific to each tent model. Given the importance of proper ventilation, We use High/Low venting in most of our tents. This allows cooler air in through the low vents and warmer, moist air up and out through the high vents. High/Low venting is accomplished within the inner tent via roof vents, doors and windows. It is important to vent the vestibule. Unvented, it can inhibit airflow into the tent. Our tent vestibules profit from the ability to “short sheet” by means of zippers & toggle

downloaded: 2   File size: 3 mb   Manafacture: Eureka! s  
Category: Camping Equipment
@name

• Work in a fully ventilated area. • Set the tent up or lay the tent out flat. Taut seams allow for even application and penetration of the sealer. • Decide which seams need to be sealed. For example, seams that will be exposed to rain, runoff, or ground level water are a must for sealing, while seams on uncoated nylon or mesh panels don’t need treatment. There is no need to seal the seams in the roof or the factory taped seams. We recommend sealing both floor and fly seams and reinforcements. •

downloaded: 0   File size: 5 mb   Manafacture: Eureka! s  
Category: Camping Equipment
@name

These actions may cut the shock cord and/or damage the pole ends. 1. Unpack the tent bag and separate the components. Unfold the tent and lay it out with the floor on the ground and with a grommeted web in each corner. Pull the tent into a rough rectangle. Do not stake down the tent just yet; but in windy conditions, stake down one corner that faces into the wind. 2. Assemble the three shockcorded tent poles. Carefully seat each section. Try to keep the poles from snapping together as this can d

downloaded: 1   File size: 5 mb   Manafacture: Eureka! s  
Category: Camping Equipment
@name

These are specific to each tent model. Given the importance of proper ventilation, We use High/Low venting in most of our tents. This allows cooler air in through the low vents and warmer, moist air up and out through the high vents. High/Low venting is accomplished within the inner tent via roof vents, doors and windows. It is important to vent the vestibule. Unvented, it can inhibit airflow into the tent. Our tent vestibules profit from the ability to “short sheet” by means of zippers & toggle

downloaded: 0   File size: 2 mb   Manafacture: Eureka! s  
Category: Camping Equipment
@name

It is important that you don’t stake the tent out too tightly. You will know it’s too tight, if the door zippers can not be easily operated. Drive stakes through the web loops, or with ring & pin, drive the stake just outside the ring so that the “J” hook catches it. Tie a piece of cord or web into a loop through the ring to be used as a large stake loop if needed. • With the tent properly staked, drape the fly over the frame, attach its tent connection points and stake down any pull outs. • Do

downloaded: 0   File size: 497 kb   Manafacture: Eureka! s  
Category: Camping Equipment
@name

Check and make sure the hub and fabric are aligned. Then, insert the proper corner ring & pin into the bottom pole section. See fig.4. FOR LIFE OUTDOORS. Assembly Instructions for the Breezeway: You can usually assemble this Breezeway alone. However, with first time set-up or with windy conditions, you will need help. Component List: 1 Screen/Body w/ Hub 1 Tent Bag 1 Pole Bag 4 Poles 1 Stake Bag and Stakes 1. Unpack the tent bag, pole bag and separate all of the components Unroll and unfol

downloaded: 0   File size: 10 mb   Manafacture: Eureka! s  
Category: Camping Equipment
@name

Tie a piece of cord or web into a loop through the ring to be used as a large stake loop if needed. • With the tent properly staked, drape the fly over the frame, attach its tent connection points and stake down any pull outs. • Do not attempt to remove the stakes by pulling on the tent becket loop, as this could cause the fabric to tear. The best way is to pry on the stake itself. Staking in special conditions: • Sand. Use long, broad stakes with plenty of surface area in loose soil. • Hard, Ro

downloaded: 0   File size: 1 mb   Manafacture: Eureka! s  
Category: Camping Equipment
@name

The best way is to pry on the stake itself. Staking in special conditions: • Sand. Use long, broad stakes with plenty of surface area in loose soil. • Hard, Rocky, or Frozen Soil. Steel stakes work best. Store steel stakes separately. Their sharp edges can cut fabric and leave rust stains, which might damage your tent. • Snow. Use “dead man” anchors. Tie tent to buried objects (branches, tent bags, or stuff sacks filled with snow; or tie tents to snow shoes, skis, or ski poles, which are stuck i

downloaded: 23   File size: 2 mb   Manafacture: Eureka! s  
Category: Camping Equipment
@name

PLAN AHEAD AND PREPARE 2. TRAVEL & CAMP ON DURABLE SURFACES 3. DISPOSE OF WASTE PROPERLY 4. LEAVE WHAT YOU FIND 5. MINIMIZE CAMPFIRE IMPACTS 6. RESPECT WILDLIFE 7. BE COURTEOUS OF OTHER VISITORS SEAM SEALING: We recommend use of a sealer such as Kenyon Seam Sealer 3 or McNett Outdoor SeamGrip®. • Work in a fully ventilated area. • Set the tent up or lay the tent out flat. Taut seams allow for even application and penetration of the sealer. • Decide which seams need to be sealed. For example, sea





Category