Login:
Votes - 4, Average rating: 3.5 ( )

User manual Clam Corp, model Fish Trap Voyager 8245

Manafacture: Clam Corp
File size: 1.17 mb
File name: 64caa0f6-ff4d-4fac-ba4c-a7de36875dfe.pdf
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


- 8245 - p/n 108304 Specifications . Height: 72” (23” packed) . Width: 72” . Depth: 93” (37” packed) ..Weight: 135 lbs. - Clam Customer Service Information - NOTICE!! Once used, this shelter cannot be returned to the store. If you have a Warranty Claim, please contact Clam Corporation Customer Service by email inquiry or direct by calling: . . Clam Corporation, Inc. 600 Clydesdale Trail Medina, MN 55340 . Phone - 763-231-4120 . Fax - 763-231-4121 . Website – . Email – Customer Service Hrs: - 8am to 4pm, Mon. - Fri. Central Standard Time Clam Corporation, Inc. Manual – 102177 - Parts List - - Parts List - Item Qty p/n Description 12 101048 Slide Block 6 101069 Canopy Pole 8 101080 1/4" Dia. X 1-1/4" Long Phillips Screw 8 101081 1/4" Flat Washer 40 101082 1/4" Thin Locknut 8 101083 Tube Cap Spacer 6 101088 1/4" Dia. X 3/4" Long Phillips Screw 1 101095 Tow Rope 1 101116 U-Channel Molding 2 101121 Porch Pole 1 101124 Short Roof Spreader Pole 1 101130 Long Roof Spreader Pole 6 101146 1-1/2" X 1-3/4" Aluminum Angle X 9" Long 12 101147 #10 X 1" Long Phillips Screw 16 101148 #6 X 3/8" Long Phillips Screw 2 101167 Front Adjustable Spreader Pole 3 101399 Seat Swivel Assembly 3 101420 Front Seat Bracket 3 101424 Rear Seat Bracket 12 101429 1-1/8" Dia. Tube Cap 2 101430 1" x 2" Rectangular Tube Cap 1 101438 1" X 2" Rectangular Support Tube 3 101442 Latch Clip 3 101466 Cloth Accessory Hammock 23 101470 1/4" Dia. X 1/2" Long Hex Head Screw 1 101479 Porch Hoop Pole 3 101482 Canopy Hoop Pole 12 101486 1/4" Dia. X 1-3/4" Long Phillips Screw 2 101487 1/4" Dia. X 2-3/4" Long Phillips Screw 2 101580 Rear Adjustable Spreader Pole 1 101584 Left Canopy Bracket 1 101585 Right Canopy Bracket 1 101626 Voyager Base 6 101652 1-1/8" Dia. Tube 3 101898 Folding Seat Assembly 1 102131 Voyager Tent - Assembly Diagram -- Assembly Diagram - 3 - Step One -- Step One - 5 - Step Two -- Step Two - - Step Three - - Step Three - -Step Four - -Step Four - 7 - Step Five -- Step Five - 8 - Step Six -- Step Six - - Step Seven - - Step Seven - Slide the Canopy Hoop Poles onto the Canopy Poles until the spring buttons engage the holes near the ends of each Canopy Hoop Pole. Support the first Canopy Hoop Pole as pictured with the Rear Adjustable Spreader Poles (the shorter of the two provided lengths). Lean the two remaining Canopy Hoop Poles against the first. 10 - Step Eight -- Step Eight - Drape the Tent over the supported hoops then go inside and spread out the Canopy Hoop Poles, attaching the Roof Velcro as you go. Orient the Porch Hoop Pole so that the holes face upward and then feed the length of the pole through the three Porch Hoop Sleeves sewn on the Tent. Slide the Porch Hoop Pole onto the Porch Poles, engaging the third hole position. Attach the Porch Hoop Velcro on each side of the Tent. Remove the Rear Adjustable Spreader Poles now supporting the hoops to allow the tent to be “set” in the next step. 11 -Step Nine - To “set” the Tent, grasp the Tent Material at the rear of the shelter and pull it downward. Observe the porch area of the tent lifting accordingly as you pull. When the U-Channel Molding is correctly installed, the Porch Hoop Pole will lightly touch the floor. To achieve this condition, start by finding the center of the Molding. From behind the unit, pull the midpoint of the Tent downward and fold the Tent Material under the Base Lip. Press the midpoint of the Molding over the Tent material and Base lip. Continue pressing outward in both directions until you have secured about twelve inches of Molding onto the Base. Having temporarily secured the Tent to the Base, take a walk around the unit. Readjust the Molding until you have verified the proper Porch Hoop Pole position and also that the Tent sides and corners are properly proportioned. When satisfied, continue applying the Molding around the shelter, one direction from center and then the other, pulling the material as you go so that surface is relatively wrinkle-free and snug. Use a side-cutters to trim the ends of the Molding if they are not equal relative to Base. Reinstall the Rear Adjustable Spreader Pole to tighten the fit of the Tent. If everything still looks good, secure the Molding with the #6 Phillips Screws. Evenly space them about every ten to twelve inches, and also put a screw in the center of both corners. Since there aren’t any predrilled holes, it's advisable to use a powered driver for this operation -Step Nine - To “set” the Tent, grasp the Tent Material at the rear of the shelter and pull it downward. Observe the porch area of the tent lifting accordingly as you pull. When the U-Channel Molding is correctly installed, the Porch Hoop Pole will lightly touch the floor. To achieve this condition, start by finding the center of the Molding. From behind the unit, pull the midpoint of the Tent downward and fold the Tent Material under the Base Lip. Press the midpoint of the Molding over the Tent material and Bas...


Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category