Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
9230-320 –Select a level campsite clear of rocks, branches and other hard or sharp objects. –Do not set up your tent under trees. Part No. 9232-322 –For best results in windy conditions, position the end of tent into the wind. Part No. 9232-324 Part No. 9232-326 Main Tent Poles for 10x7 Dome Tents (Black) Rainfly Poles for 10x7 Dome Tents (Black) Rainfly 10x7 Dome Tents Part No. 9238-328 Center Ridge Pole Connecting Room (Gray) Side Pole Connecting Room (Black) Connect Frame to Tent – Insert one end of main tent pole onto pin of pin & ring system at tent corner. (illus. 3), (illus. 4) – Go to opposite end of pole and gradually apply pressure to the pole forming an arch until you are able to insert the pin into the pole. – Repeat for second pole. (illus. 3), (illus. 4) – Repeat for second tent. (illus. 4) 1 Layout & Positioning of Tent, Pole Assembly – Layout and position tents where desired with doors facing each other. Allow aproximately 6’ between them.(illus. 1) – Unzip doors. – Partially stake down the tents using the rings of the pin & ring system at the corners of the tent. Keep the floor taut. (illus. 2) Do not fully stake down, you may need to make adjustment s later. – Assemble main tent poles (black) by interlocking shock-corded poles. This will make two long poles for each tent. – Insert the poles diagonally into pole sleeves. The center of the poles should cross forming an “X” in the middle of tent. (illus. 1) 2 Assembled black main tent poles inserted through pole sleeves illus. 2 Tent stake through ring on stake loop Doors Attach Tent to Frame Using Frame Clips3 illus. 1 Tents positioned with poles through poles sleeves illus. 3 Assembled tents without rainflys illus. 5 Frame clips illus. 4 – Attach frame clips along the edges of tent to frame poles. (illus. 3), (illus. 5) – Make any adjustments to the tent corner stakes that are needed. Insert pin into pole end 4 illus. 6 Insert rainfly pole piece into pockets on underside of rainfly illus. 8 Hooks attaches to fabric loop Underside of rainfly attaches to tent frame Attach Tent Rainflys – Assemble tent rainfly poles by interlocking shock-corded pole. – Insert rainfly pole into the pole pocket located at the center edges of the underside of rainfly. (illus. 6), (illus. 7) – Drape rainfly over tent frame, pole side down. Rainfly pole should be over door and rear window. NOTE: The toggles on the rainfly need to run from the front corners to the top of the tent. – Connect the four elastic loops with hooks, (found at the rainfly corners) to the fabric loops on the bottom row of frame clips. – Secure rainfly with attachments located on underside of fly. (illus. 7) – Repeat for second tent. Connecting Room – Layout connecting room and assemble center ridge and side poles. – Insert the center ridge pole (gray) through ridge pole sleeves and insert the pole ends into the pole pockets. (illus. 9) – Insert the side poles through the pole sleeves on connecting room. (illus. 9) Position connecting room between tents, pole side up. – Insert one end of side pole onto pin of pin & ring system on the stability strap. (illus. 3) – Go to opposite end of pole and gradually apply pressure to the pole forming an arch until you are able to insert the pin into the pole. – Repeat for second pole. (illus. 9), (illus. 10) – Move tent as needed for better fit with connecting room. Fully stake down tents. – Attach connecting room to the tents with toggles & loops on rainfly and hooking the stake loop ring at the tent corners. (illus. 10) – Stake out the tents with (2) side guylines each and the connecting room with (4) guylines. (illus. 8) illus. 7 Both tents fully assembled with rainflys illus. 9 Connecting room with center ridge pole and side poles in position illus. 10 Both tents and connecting room completed GuylinesStability strap Toggles & Loops secure connecting room to tents Center ridge pole sleeves Pole pocket 5 4 illus. 6 Insert rainfly pole piece into pockets on underside of rainfly illus. 8 Hooks attaches to fabric loop Underside of rainfly attaches to tent frame Attach Tent Rainflys – Assemble tent rainfly poles by interlocking shock-corded pole. – Insert rainfly pole into the pole pocket located at the center edges of the underside of rainfly. (illus. 6), (illus. 7) – Drape rainfly over tent frame, pole side down. Rainfly pole should be over door and rear window. NOTE: The toggles on the rainfly need to run from the front corners to the top of the tent. – Connect the four elastic loops with hooks, (found at the rainfly corners) to the fabric loops on the bottom row of frame clips. – Secure rainfly with attachments located on underside of fly. (illus. 7) – Repeat for second tent. Connecting Room – Layout connecting room and assemble center ridge and side poles. – Insert the center ridge pole (gray) through ridge pole sleeves and insert the pole ends into the pole pockets. (illus. 9) – Insert the side poles through the pole sleeves on connecting room. (illus....