Votes - 2, Average rating: 4
(
)
)
|
manual abstract
• Secure with all stakes and guylines provided to prevent property damage or personal injury. • For best results in windy conditions, position narrow end of tent into the wind. • Enlist the help of at least one other person to assist you when it is time to assemble the tent. Pole Descriptions Pole Pole Pole Description Qty. Dia. Repair Kit Replacement Kit Long Leg Pole, steel (w/ red marking) 2 19mm N/A 5010000614 Short Leg Pole, steel 4 19mm N/A 5010000623 Curved Ridge Pole, steel (w/ red marking) 1 19mm N/A 5010000613 Curved Ridge Pole, steel 2 19mm N/A 5010000615 Side Window Pole, black, fiberglass, metal tips 2 8.5mm 5010000541 5010000547 Door Pole, long, thin ,black, fiberglass, rubber tips 1 6.3mm 5010000543 5010000545 Vert. Door Pole, short, black, fiberglass, rubber tips 1 6.3mm 5010000543 5010000545 To Set Up Tent 1. Unfold tent and spread out on a clean, level surface with the door facing the desired direction. Unzip doors. (Fig. 1) Door Fig. 1 2. Pull four corners of tent taut, then secure by driving stakes through web loops at an angle for better anchoring. (Fig. 2) Fig. 2 3. Assemble three, steel, shock-corded, curved Ridge Poles. Insert Ridge Pole (with red marking) into center sleeve on top of tent with the red trim (Fig. 3). Insert the remaining curved Ridge Poles into the other two sleeves on top of tent. Ridge Pole with Red Marking Fig. 3 Sleeve with Red Trim 4. Assemble six, steel, shock-corded, Leg Poles. Push down on steel button on tapered end and insert into end with four holes. NOTE: Make sure steel button locks into third hole on pole as shown. (Fig.4) 5. Insert curved end of Leg Poles (with red marking) into the ends of the Ridge Pole (with red marking). Insert curved end of remaining short Leg Poles into the ends of the remaining Ridge Poles. (Fig. 5 & 6) Button in third hole Fig. 4 Ridge Pole with Red Marking Fig. 5 Sleeve with Red Trim Curved End of Long Leg Pole Fig. 6Ridge Pole with Red Marking in center sleeve 6. Rotate all six Leg Poles upright and insert pin on each web loop at the side locations as shown. (Fig. 7 & 7A) Fig. 7 7A Pin 7C Metal Tip 7B Sleeve Window Pole Hole in Leg Pole 6. Assemble the two, shock-corded, black Window Poles, then insert one into sleeve located at each end of tent. (Fig. 7 & 7B) 7. Insert tapered metal tip on Window Pole into Leg Pole. NOTE: It may be necessary to gently rotate Leg Pole so the hole will line up with the Window Pole. 8. Go to opposite end of each window pole and gradually apply pressure to the pole forming an arch. Insert the pin into the leg pole end at the corners of tent. (Fig. 7 & 7C) 9. Locate the plastic hooks at sides and corners of tent, then snap onto Leg Poles to attach. (Fig. 8) 10. Locate web strap with plastic hook on the sides of each end panel Window Vent, then snap onto the corner Leg Pole. (Fig. 9) Fig. 9 Window Vent Web Tent Strap Corner Leg Pole Fig. 8 11. To stretch tent to finished size: • Push in button on Leg Pole while twisting lower Leg Pole section counterclockwise (Fig.10); • Pull up on top Leg Pole section until tent is taut; • Twist the lower Leg Pole clockwise until the button locks into the center or lowest hole; • Repeat on remaining Leg Poles. 12. Insert plastic stakes through web straps located on both sides of tent, then drive in to secure. (Fig. 11) Fig. 11 Fig. 10 Button Center Hole Lower Hole Lower Leg Pole Section Upper Leg Pole Section Hinged, Rigid Door 1. Assemble Vertical Door Pole (shorter black pole with plastic cap tips); then insert through zippered sleeve on side of door and into hinge. (Fig. 12) Fig. 12Sleeve Hinge (continued on other side) STITCH LINE Hinged, Rigid Door (continued) 2. Insert end of Vertical Door Pole into bottom hinge plate, apply pressure to form a slight bow, then insert other tip of pole into top hinge. Zip up vertical sleeve. (Fig. 13 & 14) 3. Assemble Door Pole (longer black pole with plastic cap tips); then insert into zippered sleeve at top of door. (Fig. 15) 4. Insert end of Door Pole into top hinge plate, apply pressure to form a bow, then insert other tip of pole into the bottom hinge. (Fig. 16) 5. Zip up sleeve to enclose Door Pole. (Fig. 17) Fig. 13 Fig. 14 Pole Sleeve Fig. 15 Fig. 16 Fig. 17 Pole Sleeve To Attach Rainfly 1. Drape Rainfly over tent. Make sure seams on Rainfly are facing down and centered over poles of the tent. (Fig. 18) NOTE: Hook and loop fasteners, located on seams of under side of rainfly, should be centered over black and gray poles. Fig. 18 Rainfly 2.Locate all hook & loop fasteners on underside of Rainfly and wrap around each Leg Pole and Window Vent Pole locations. (Fig. 19) 3.Insert metal hook on elastic straps on Rainfly into the hole on each Leg Pole. (Fig 20 & 21) Fig. 20 Fig. 21Fig. 19 Fig. 22 Center Leg Pole Location End Leg Pole Location 4. Loop ends of guylines over stakes, stretch tight, then hammer into ground at an angle as shown. (Fig. 22 & 22A) 22A Guyline Attaching Room Divider 1. Divider Panel can be installed t...