Votes - 2, Average rating: 4.5
(
)
)
|
manual abstract
Backrest Adjustment Tube Leg Lever Seat Assembled Dimensions: Height: 72O Base: 56O x 84O 4 Part Identification ChartNModel No. IMBE40890 R0999A M10 x 19mm Bolt (57).1 M6 Washer (30).4 M8 Washer (23).2 M10 Washer (6).15 M10 x 48mm Bolt (55).2 M8 Nylon Locknut (13).2 M10 Nylon Locknut (11).29 M10 x 62mm Carriage Bolt (59).2 M8 x 64mm Bolt (43).1 M10 x 65mm Bolt (67).5 M10 x 68mm Bolt (33).5 M8 x 68mm Bolt (60).1 M10 x 72mm Bolt (68).8 Protector Strip Screw (49).14 M10 x 75mm Bolt (8).1 M10 x102mm Bolt (71).1 M6 x 16mm Screw (3).6 M6 x 38mm Screw (4).4 M10 x108mm Bolt (34).3 M10 x 168mm Bolt (22).1 5 Assembly Before beginning assembly, carefully read the following information and instructions: Make Things Easier for Yourself! Everything in this manual is designed to ensure that our products can be assembled successfully by anyone. However, it is important to recognize that this is a sophisticated product with many small parts and, consequently, assembly will take time. Most people find that by setting aside plenty of time, and by deciding to make the task enjoyable, assembly will go smoothly. • Assembly requires two people. • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. • Tighten all parts as you assemble them, unless instructed to do otherwise. 1. Before beginning assembly, make sure that you understand the information in the box above. Note: Some of the parts described in the assembly steps may be pre-assembled. Press a 2O Square Inner Cap (17) into the indicated end of the Right Stabilizer (26). Press a 2O Square Outer Cap (58) onto the other end of the Stabilizer. Press a 48mm Round Inner Cap (12) into each end of the welded tube on the Right Stabilizer (26). Press a 1.5O Square Inner Cap (72) into the storage tube on the Right Upright (2). Slide the Right Upright (2) onto the Right Stabilizer (26) as shown. Attach the Upright to the Stabilizer with an M10 x 65mm Bolt (67), two M10 Washers (6) and an M10 Nylon Locknut (11). Do not tighten the Nylon Locknut yet. Set the upright assembly aside and make sure it cannot fall over. • For help identifying the small parts, use the PART IDENTIFICATION CHART on page 5. • As you assemble the weight bench, make sure all parts are oriented as shown in the drawings. The following tools (not included) are required for assembly: . Two (2) adjustable wrenches . One (1) rubber mallet . One (1) standard screwdriver . One (1) phillips screwdriver . Lubricant, such as grease or petroleum jelly plus soapy water. Assembly will be more convenient if you have the following tools: A socket set, a set of open-end or closed-end wrenches or a set of ratchet wrenches. 1 2 72 26 67 12 6 17 12 6 11 6 2. Press a 2O Square Outer Cap (58) onto each end of the Left Stabilizer (25). Press a 51mm x 76mm Inner Cap (24) into the top of the Left Upright (1). Insert two M10 x 62mm Carriage Bolts (59) into the holes in the Left Stabilizer (25) from below. Slide the Left Upright (1) onto the Left Stabilizer (25) as shown, so the bracket on the Left Upright fits over the M10 x 62mm Carriage Bolts (59) in the Left Stabilizer. Attach the Left Upright (1) to the Left Stabilizer (25) with an M10 x 65mm Bolt (67), two M10 Washers (6), and an M10 Nylon Locknut (11). Thread an M10 Nylon Locknut onto each of the M10 x 62mm Carriage Bolts (59) in the Stabilizer. Do not tighten the Nylon Locknuts yet. 3. Align the holes in a 4-hole Support Plate (16) with the holes in the Right Upright (2). Insert four M10 x 72mm Bolts (68) into the Support Plate and the Right Upright. Make sure that the Bolts are inserted from the direction shown. Align the holes in another 4-hole Support Plate (16) with the holes in the Left Upright (1). Insert four M10 x 72mm Bolts (68) into the Support Plate and the Left Upright. Make sure that the Bolts are inserted from the direction shown. While a second person holds the Right Upright (2), slide the bracket on the Crossbar (20) over the four M10 x 72mm Bolts (68) in the Right Upright. Make sure that the Crossbar is turned so the warning decal is on top. Attach the Crossbar with four M10 Nylon Locknuts (11). Do not tighten the Nylon Locknuts yet. Attach the Crossbar (20) to the Left Upright (1) as described above. 3 2 1 24 59 25 67 11 6 6 11 58 58 1 68 68 68 68 16 16 2 20 Decal 11 11 11 11 7 4. Snap a Carriage Bushing (56) into the Weight Stop (53). Slide both parts onto the Rear Upright (9), making sure that the Carriage Bushing (56) is on top. Attach the parts to the indicated hole in the Rear Upright with an M8 x 68mm Bolt (60) and an M8 Nylon Locknut (13). Next, slide the Rear Upright (9) onto the Right Stabilizer (26). Make sure that the Rear Upright is turned so the upper end slants in the direction shown. Attach the Rear Upright with an M10 x 65mm Bolt (67), two M10 Washers (6), and an M10 Nylon Locknut (11). Do not tighten the Nylon Locknut yet. 5. Press Carriage Bushings (56) into the to...