Votes - 2, Average rating: 3.5 ( )

Manafacture: Horizon Fitness File size: 4.01 mb File name: Elite_1.2E_2.2E.pdf Language of manual:

B) To attach LOWER LINK ARM to PEDAL ARM, slide SPACER (J), FLAT WASHER (K) and WAVY WASHER (L) onto PEDAL ARM BRACKET. NOTE: Attaching the lower link arm assembly to the pedal arm first makes assembly of the linkage arms less difficult. C) Slide LOWER LINK ARM onto PEDAL ARM BRACKET, followed by FLAT WASHER (M) and BOLT (N). D) Repeat on other side. E) Slide LOWER LINK ARM onto UPPER HANDLEBAR and attach using 2 PRE-ATTACHED SET SCREWS. F) Attach HANDLEBAR COVERS using 2 SCREWS (O). G) Repeat on other side. .................... .............................. ........................ .................... ............................ ................ .............................. .............................. .............................. .................... .................................. .................... .................... ............ .............................. .......... ............ ........ .................... .......... ............ ................ .......... ............ .................. .......... ............ ........ .................... .......... ............ HARDWARE BAG FOR STEP 6 CONTENTS : ASSEMBLY STEP 6 NOTE: There is NO hardware bag for this step. All hardware is preinstalled. A) Pull TENSION CABLE out from square hole in console mast. B) Turn RESISTANCE KNOB to highest resistance setting. Place the TENSION WIRE into the BOTTOM KEY HOLE on the RESISTANCE KNOB BRACKET. C) While holding the RESISTANCE KNOB BRACKET, pull the RESISTANCE KNOB up to slide it into the TOP KEY HOLE position on the RESISTANCE KNOB BRACKET. D) Once the TENSION WIRE is in position, turn the RESISTANCE KNOB to the lowest resistance setting. E) Slide RESISTANCE KNOB & BRACKET into the CONSOLE MAST and attach using PRE-INSTALLED BOLT & WASHER. F) Attach the CONSOLE WIRES (2 heart rate wires and 1 speed sensor wire). G) Carefully tuck the CONSOLE WIRES into the CONSOLE MAST before attaching the CONSOLE. H) Attach CONSOLE to the CONSOLE MAST using the 2 PRE-ATTACHED SCREWS (screws will have to be removed from the console first). DO NOT PINCH WIRES! ASSEMBLY STEP 7 YOU’RE FINISHED! .................... ........ ........................ .................... ........................ .............. .......... .......................... .......................... ........................ .............................. STEPS A-E ........................ ............ STEPS F-H Elite 1.2E 2.2E Rev.1.0.indd 10-11 7/19/05 8:20:19 AM 12 INTRODUCTION IMPORTANT PRECAUTIONS ASSEMBLY BEFORE YOU BEGIN ELLIPTICAL OPERATION LIMITED WARRANTY TROUBLESHOOTING & MAINTENANCE CONDITIONING GUIDELINES BEFORE YOU BEGIN ASSEMBLY 13 IMPORTANT INTRODUCTION PRECAUTIONS ELLIPTICAL OPERATION CONDITIONING GUIDELINES TROUBLESHOOTING & MAINTENANCE LIMITED WARRANTY .............................. .............................. ............................ .......................... c ................................ c ................................ c .......................................... c ...................................... c ................................ .................... ........................ .................................. .............. ............................ c .................. c ............................ c ...................................... c .................................. c .................................... c .................................... c ...................... c ........................ c .................................... c .......................... c ........................................ c ................................................ c .............................................. c ............................ c .............................. ................................ .............................. .............................. .............................. ................ .................. .................................................................................................................................................................................................................... ............................................................................................................................................................................ .................... ...................................... ................................ A) Open HARDWARE BAG FOR STEP 1. B) Attach STABILIZER TUBE to the MAIN FRAME using 2 BOLTS (A). A) Open HARDWARE BAG FOR STEP 2. B) Slide left and right GUIDE RAILS into MAIN FRAME. C) Attach GUIDE RAILS using 2 BOLTS (B). NOTE: You may have to rotate the guide rails back and forth to get them to slide into the frame. ................ .............................. .................... ................ .......... ............ HARDWARE BAG FOR STEP 1 CONTENTS : ASSEMBLY STEP 1 ASSEMBLY STEP 2 .................. .................... ................ .......... ............ HARDWARE BAG FOR STEP 2 CO...

Download now

Please, enter two numbers from picture: