Votes - 1, Average rating: 5 ( )

Manafacture: Horizon Fitness File size: 1.3 mb File name: 2.1E_4.1E_Users_Guide.pdf Language of manual:

PLEASE CALL OUR TOLL-FREE DIRECT CUSTOMER ASSISTANCE CENTER @ 1-800-244-4192 Mon.-Fri., 8 a.m.-5 p.m. CST (excluding holidays). 7 2.1E HARDWARE A) 20mm Bolt Quantity: 2 Coated Washer Quantity: 4 C) 12mm Bolt Quantity: 3 D) 15mm Bolt Quantity: 6 E) 8mm Set Screw Quantity: 4 F) 17mm Nut Qauntity: 2 G) 13mm Nut Quantity: 3 H) 20mm Screw Quantity: 2 I) 15mm Screw Quantity: 4 J) Arc Washer Quantity: 3 B) 70mm Bolt Q) 8mm Bolt Quantity: 8 L) Wavy Washer Quantity: 2 R) White Teflon Washer Quantity: 4 S) Sleeve Quantity: 2 I U) Lock Washer T) 40mm Bolt Quantity: 2 Quantity: 1 Quantity: 1 8 STEP 1: ATTACH FRONT TUBE. Note: Make sure not to tighten bolts until all assembly steps have been completely assembled and aligned. STEP 4: ATTACH LEFT & RIGHT PEDAL ARMS AND PEDAL ARM COVERS. Note: Black ‘Teflon’ surface of K should be facing the pedal arm. STEP 7: ATTACH LEFT & RIGHT LINK ARMS TO THE LEFT & RIGHT LOWER HANDLE BARS. STEP 2: ATTACH LEFT & RIGHT GUIDE RAILS. STEP 5: ATTACH LEFT & RIGHT LOWER HANDLE BARS TO CONSOLE MAST AND ATTACH LEFT & RIGHT UPPER HANDLEBARS. ATTACH H-BAR COVERS. Note: Bolts and washers are pre-assem-bled. STEP 8: ATTACH TENSION KNOB ATTACH CONSOLE MAST AND CONSOLE MAST BOOT. Note: Make sure to loosen the water bottle screws in order to fit the console cable through the mast. DO NOT PINCH WIRES! STEP 6: ATTACH LEFT & RIGHT FOOT PADS TO FOOT PLATE/LINK ARM. ATTACH PIVOTING FOOT PLATE TO PEDAL ARM. 9 STEP 9: ATTACH CONSOLE AND CONNECT ALL WIRES. Note: DO NOT PINCH WIRES! Note: Bolts are pre-assembled to console. Assembly 4.1E ASSEMBLY UNPACKING Unpack the product where you will be using it. Place the product on a level flat surface. It is recommended that you place a protective covering on your floor. Note: It is recommended that you apply grease to the threads of each bolt as you assemble the product, to prevent loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY! Place your elliptical trainer on a level flat surface. It is recommended that you place a protective covering on your floor. PARTS • 1 Front Foot Tube • 2 Upper Handlebars • 2 Lower Handlebars • 2 Pedal Link Arms • 2 Foot Pads • 2 Pedal arms • 2 Guide Rails • 1 Console • 1 Console Mast • 1 Console Mast Boot • 1 Rear Rail Stabilizer • 1 Power Supply • 2 Crank Boots • 2 Front Upper Handlebar Covers • 2 Back Upper Handlebar Covers • 1 Hardware Pack TOOLS (included) • 4mm Allen Wrench • 5mm Allen Wrench/ Phillips Screw Driver • 13/15mm Flat Wrench • 17mm Wrench If you have any questions, or if there are any missing parts, we will guarantee complete satisfaction. PLEASE CALL OUR TOLL-FREE DIRECT CUSTOMER ASSISTANCE CENTER @ 1-800-244-4192 Mon.-Fri., 8 a.m.-5 p.m. CST (excluding holidays). 10 4.1E HARDWARE A) 20mm Bolt Quantity: 2 V) Arc Washer Quantity: 4 C) 12mm Bolt Quantity: 3 E) 8mm Set Screw Quantity: 4 D) 15mm Bolt Quantity: 6 F) 17mm Nut Qauntity: 6 V I) 15mm Screw Quantity: 4 H) 20mm Screw Quantity: 2 J) Arc Washer Quantity: 3 B) 70mm Bolt Quantity: 1 /7s K) 70mm Bolt Quantity: 4 G) 13mm Nut Quantity: 3 L) Wavy Washer Quantity: 2 U) Lock Washer Quantity: 3 S) Sleeve Quantity: 2 I Q) 8mm Bolt R) White Teflon Washer T) 40mm Bolt Quantity: 2 Coated Washer Quantity: 4 STEP 1: ATTACH FRONT TUBE. Note: Make sure not to tighten bolts until all assembly steps have been completely assembled and aligned. STEP 2: ATTACH LEFT & RIGHT GUIDE RAILS AND REAR RAIL STABILIZER. Note: Make sure all the levelers are leveled. STEP 3: ATTACH CONSOLE MAST AND CONSOLE MAST BOOT. Note: Make sure to loosen the water bottle screws in order to fit the console cable through the mast. DO NOT PINCH WIRES! STEP 4: ATTACH LEFT & RIGHT PEDAL ARMS AND PEDAL ARM COVERS Note: Black ‘Teflon’ surface of W should be facing the pedal arm. STEP 5: ATTACH LEFT & RIGHT LOWER HANDLE BARS TO CONSOLE MAST AND ATTACH LEFT & RIGHT UPPER HANDLE BARS. ATTACH H-BAR COVERS. Note: Bolts and washers are preassembled. STEP 6: ATTACH LEFT & RIGHT FOOT PADS TO FOOT PLATE/LINK ARM. ATTACH PIVOTING FOOT PLATE TO PEDAL ARM. STEP 7: ATTACH LEFT & RIGHT LINK ARMS TO LEFT & RIGHT LOWER HANDLE BARS. STEP 8: ATTACH CONSOLE AND CONNECT ALL WIRES. Note: DO NOT PINCH WIRES! Note: Bolts are pre-assembled to console. 12 Elliptical Operation & Adjustments POWER The console on your (2.1E) is powered by 2 AA batteries, which are replaceable through the back side of the console. Your elliptical itself, is powered by you. Your programmable (4.1E) elliptical trainer is powered by a power supply. The power supply must be plugged into the power jack, which is located in the front of the machine near the front foot tube. LEVELING The elliptical trainer should be level for optimum use. Once you have placed the elliptica...

Download now

Please, enter two numbers from picture: