Votes - , Average rating:
(
)
)
Manafacture: Vision Fitness
File size: 854.16 kb
File name: e807399a-5929-499d-b74d-7319857d844a.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
Be sure to read your Owner’s Guide before using your new Fitness Bike. If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12 NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before completely tightening any ONE screw. 1STEP2STEP4STEP3STEP TOOLS & PARTS INCLUDED 14mm Seat Wrench 15mm Pedal Wrench 5mm T-Shaped Wrench Screwdriver 5mm L-Shaped Wrench PARTS BOX Water Bottle & Bracket Power Supply (E3100 ONLY) Tension Control Knob and bracket (E3000 ONLY) Pedals Seat Post Knob Color-coded Hardware Bags Owner’s Guide Assembly Guide Warranty Card HARDWARE INCLUDED ORANGE BAG M8 x 20L Screw Quantity: 2 M8 Lockwasher Quantity: 4 M8 x 65L Screw Quantity: 2 PINK BAG M5 x 70L Screws Quantity: 1 (E3000 ONLY) M8 x 15L Screw Quantity: 7 M8 Lockwashers Quantity: 8 M8 x 20L Screw Quantity: 2 M5 x 15L Screw Quantity: 2 M5 Washer Quantity: 1 (E3000 ONLY) 1STEP• Slide the rear foot into place and insert two screws (M8x20L) with two lock washers (M8) to the outside holes. Insert two screws (M8x65L) with two lock washers (M8) to the inside holes. Tighten all screws with the 5mm T-Shaped wrench. ORANGE BAG • Slide the rear foot into place and insert two screws (M8x20L) with two lock washers (M8) to the outside holes. Insert two screws (M8x65L) with two lock washers (M8) to the inside holes. Tighten all screws with the 5mm T-Shaped wrench. ORANGE BAG 1STEPRear Foot 5 6 E3000 ONLY STEP 2 Tension Knob Tension Knob Bracket Console Mast Console Mast Cover Mounting Bracket STEP 2 • Slide the console mast cover onto the console mast. • With the included wire-tie, pull the wire harness, or sensor wire through the console mast. Insert the console mast into the mast mounting-bracket. Secure in place with seven screws (M8x15L) and six lock washers (M8). Tighten with the 5mm T-Shaped wrench. NOTE: The screw facing the seat does not use a lock washer. Tighten this screw until snug with the 5mm L-Shaped wrench. Slide the console mast cover down over the screw heads. • MODEL E3000: Snap the tension knob mounting bracket onto the tension knob. Turn the tension knob to level 16. Connect the cable to the tension cable located inside the console mast. Secure the tension knob to the console mast with the washer (M5) and screw (M5x70L). Tighten with screwdriver. • Slide the heart rate wires of the handlebar through the hole in the handlebar bracket on the console mast. Secure the handlebar onto the handlebar bracket with two screws (M8x20L) and two lock washers (M8). Tighten with the 5mm T-Shaped wrench. • Remove the four mounting screws from the back of the console. Connect the wire harness and the heart rate wires to the console. Attach the console to the console mast using the four mounting screws that were just removed. • E3000 ONLY: Insert the two AA batteries into the console. • Attach the water bottle cage to the console mast with two screws (M5x15L) using the screwdriver. Insert the water bottle into the cage. PINK BAG E3100 ONLY Console Water Bottle Cage STEP 3 Seat Post Seat Post Cover 3STEP• Slide the seat post cover onto the seat post • Slide the seat post into the frame and lower the seat post cover into place. • Insert the adjustment knob through the seat post cover and tighten in place. • Attach the seat to the seat post by tightening the 14mm nuts on the underside of the seat. GREEN BAG 3STEPSeat Post Seat Post Cover 3STEP• Slide the seat post cover onto the seat post • Slide the seat post into the frame and lower the seat post cover into place. • Insert the adjustment knob through the seat post cover and tighten in place. • Attach the seat to the seat post by tightening the 14mm nuts on the underside of the seat. GREEN BAG 7 4STEP• Attach the left and right pedals to the left and right crank arms, tighten using the 15mm pedal wrench. PEDALS 4STEP4STEP• Attach the left and right pedals to the left and right crank arms, tighten using the 15mm pedal wrench. PEDALS 4STEP 500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551 toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373 ©2005 Vision Fitness. All Rights Reserved. 5.05 Part #Z30CB112-AG AG18.18PRD REV4 8 ...