Votes - 3, Average rating: 4.3 ( )

Manafacture: NordicTrack File size: 698.11 kb File name: b2f3373b-e8fa-4dd0-9a54-b1cf8c871470.pdf Language of manual:

First, insert the Fastener Bases through the Cover Panel and into the Main Frame. Next, push a Fastener Pin (58) into the hole in each Fastener Base until it is flush with the Base. 4. Lubricate an Frame Axle (13). Attach the Handlebar Swing Arm (5) to the Main Frame (1) with the Frame Axle, two Rubber Washers (51), and two Axle Fasteners (56). Note: If the ends of the Frame Axles (13) are internally threaded, the Axle Fasteners (56) will be bolts; if the ends are externally threaded, the Axle Fasteners will be acorn nuts (see the PART IDENTIFICATION CHART on page 4). 4 3 1 56 51 51 56 5 Lubricate—13 2 6 7 45 45 58 58 2 21 49 10 7 11 17 5 5 6 51 56 36 Hole 1 4 51 5. Push the Magnet Bracket (36) into the hole in the Pedal Frame (4). Lubricate an Frame Axle (13). Attach the Pedal Frame (4) to the Main Frame (1) with the Frame Axle (13), two Rubber Washers (51), and two Axle Fasteners (56). 6. Attach the Left Side Shield (21) to the Seat Frame (2) using three Fastener Bases (45) and three Fastener Pins (58). First, insert the Fastener Bases through the Side Shield and into the Seat Frame. Next, push the Fastener Pin (58) into the hole in each Fastener Base until it is flush with the Base. Attach the Right Side Shield (22, not shown) in the same way. 7. While another person holds the Long Link Arm (10) and the Short Link Arm (11) in place, put two Plastic Washers (49) between them. Then, connect the Seat Swing Arm (5), the Long Link Arm (10), and the Short Link Arm (11) using an M8 x 1.375” Bolt (17) and an M8 Nylon Jam Nut (7). 8. Place the Seat (20) on the Frame (2). Slide the Seat Washer (38) onto the Seat Knob Bolt (43) and then tighten the Seat Knob (37) onto it. Slide the Weight Bracket (8) onto the Seat Frame (2) so that it slants away from the AEROBIC RIDER 2. Align the holes in the Weight Bracket with the ones in the end of the Frame. Insert the M8 x 120mm Bolt through the Weight Bracket and the Frame and secure it with an M8 Nylon Jam Nut (7). 8 2 20 43 38 57 7 37 8 Lubricate—13 56 9. Depress the two buttons on the sides of the Handlebar Assembly (6) with your thumb and forefinger. Insert the Handlebar Assembly (6) into the Handlebar Swing Arm (5). Make sure that the buttons protrude through one of the two sets of holes in the Handlebar Swing Arm. The upper holes offer lower workout resistance; the lower holes offer higher resistance. 10. Slide the Monitor (35) fully onto the Main Frame (1) as shown in inset drawing A. Press down on the Monitor as shown in inset drawing B until it snaps into place. 11. Remove the battery cover from the Monitor (35). Insert two new AA batteries into the Monitor. Identify the negative (–) and positive (+) ends of the batteries. The springs in the battery compartment should touch the negative ends of the batteries. 9 6 Buttons Holes 5 10 35 1 A 35 1 B 35 1 11 35 (+) (–) (–) Battery Cover AA Batteries (+) 12. Make sure that all parts are properly tightened. To protect the floor or carpet from damage, place a ma...

Download now

Please, enter two numbers from picture: