Votes - 3, Average rating: 4
(
)
)
|
manual abstract
DESCRIPTION QTY. ORDER NO. NO. DESCRIPTION QTY. ORDER NO. 57 M10 X 136MM BOLT 1 6.25-57 86 REAR ROLLER SHAFT 1 6.25-86 58 MOTOR HOLDER 1 6.25-58 87 M6 X 70 ALLEN BOLT 3 6.25-87 SIDE RAIL END CAP 59 DRIVING MOTOR 1 6.25-59 88 LEFT 1 6.25-88 SIDE RAIL END CAP 60 ELEVATION MOTOR 1 6.25-60 89 RIGHT 1 6.25-89 ELEVATION GEAR 61 SLEEVE 1 6.25-61 90 M8 NYLON NUT 4 6.25-90 62 4 X 12 WASHER 10 6.25-62 91 M8 X 43MM BOLT 2 6.25-91 ELEVATION SUPPORT 63 #8 X 25 SCREW 10 6.25-63 92 CAP 2 6.25-92 ELEVATION SUPPORT 64 N/A 93 TUBE COVER - LEFT 1 6.25-93 65 SIDE RAIL - LEFT 1 6.25-65 94 M10 X 63MM BOLT 1 6.25-94 RUNNING DECK 66 SUPPORT TUBE 1 6.25-66 95 M10 X 90MM BOLT 1 6.25-95 DECK FRAME SIDE ELEVATION SUPPORT 67 COVER - LEFT 1 6.25-67 96 TUBE 1 6.25-96 MOTOR CONTROL ELEVATION SUPPORT 68 BOARD 1 6.25-68 97 TUBE COVER - RIGHT 1 6.25-97 ELEVATION CONTROL PLASTIC CLAMP - 69 BOARD 1 6.25-69 98 BOTTOM 2 6.25-98 CONSOLE SUPPORT 70 M10 X 35MM BOLT 1 6.25-70 99 FIXING PLATE 2 6.25-99 BASE FRAME ROUND 71 DECK FRAME 1 6.25-71 100 ENDCAP 2 6.25-100 72 6 X 13 WASHER 3 6.25-72 101 M8X40BOLT 1 6.25-101 REAR TRANSPORTATION 73 FRONT ROLLER 1 6.25-73 102 WHEEL 1 6.25-102 M8 X 80MM ALLEN 74 FRONT ROLLER SHAFT 1 6.25-74 103 BOLT 2 6.25-103 75 DRIVING BELT 1 6.25-75 104 CURVE WASHER 2 6.25-104 DECK RUBBER 76 CUSHION 2 6.25-76 105 BOLT 2 6.25-105 CONSOLE HOUSING 77 SIDE RAIL - RIGHT 1 6.25-77 106 UPPER 1 6.25-106 SAFETY KEY WIRE - CONSOLE HOUSING 78 UPPER SECTION 1 6.25-78 107 BOTTOM 1 6.25-107 WATER BOTTLE 79 PLASTIC BUSHING 2 6.25-79 108 HOLDER 2 6.25-108 GLOVE COMPARTMENT 80 10MM SHAFT 1 6.25-80 109 FRAME 2 6.25-109 DECK FRAME SIDE GLOVE COMPARTMENT 81 COVER - RIGHT 1 6.25-81 110 COVER 2 6.25-110 82 PLASTIC CLAMP - TOP 2 6.25-82 111 M6 x 50mm Allen Bolt 2 6.25-111 83 ELEVATION SUPPORT 2 6.25-83 112 SPRING 1 6.25-112 84 DECK FRAME - REAR 1 6.25-84 113 FOLD UP SENSOR 1 6.25-113 TRANSPORTATION 85 REAR ROLLER 1 6.25-85 114 WHEEL BRACKET 1 6.25-114 TRANSPORTATION WHEEL BRACKET 115 PIVOT 1 6.25-115 FRONT HANDLEBAR 116 FIXING BOLT 2 6.25-116 EKG PULSE WIRE – 117 UPPER SECTION 2 6.25-117 EKG PULSE WIRE – 118 LOWER SECTION 2 6.26-118 119 M6 x 16mm Allen Bolt 2 6.25-119 HARDWARE PACK (not shown on exploded 120 diagram) 1 6.25-120 Visit us at: SMOOTH 6.25 MOTORIZED TREADMILL Visit us at: 8 PARTS DIAGRAM A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PREASSEMBLED AT THE FACTORY. 2 9 10 11 11 9 10 12 13 14 23 25 22 25 27 28 33 30 31 32 34 38 39 40 41 42 43 44 29 36 37 78 7 52 24 45 45 15 35 15 23 8 1 3 4 6 17 18 19 20 21 21 16 5 5 99 99 100 100 56 56 103 104 103 104 15 15 15 105 105 15 15 108 106 107 109 110 115 112 114 90 102 113 101 116 116 111 117 117 118 104 104 SMOOTH 6.25 MOTORIZED TREADMILL Visit us at: 9 PARTS DIAGRAM A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PREASSEMBLED AT THE FACTORY. 46 47 62 48 63 62 63 65 49 50 21 90 53 54 26 57 60 61 66 15 67 58 55 51 15 76 68 69 26 70 59 72 87 81 15 73 74 75 77 92 15 93 56 83 98 26 26 94 95 96 97 15 92 82 82 80 79 44 71 85 86 72 87 15 88 89 90 25 91 84 119 119 SMOOTH 6.25 MOTORIZED TREADMILL Visit us at: 10 ASSEMBLY STEP 1: Remove packing material form the treadmill carton as shown in FIG 1. Please refer to the page 21 “Folding Instruction” to fold up the running deck. Remove the parts that underneath the running deck. Refer to the page 22 “Unfolding Instruction” to unfold the running deck. FIG. 1 SMOOTH 6.25 MOTORIZED TREADMILL Visit us at: 11 ASSEMBLY STEP 2: Attach the Left Upright (13) and Right Upright (14) to Console Support Tube (12) with four M8 x 55mm Allen Bolt (5) and two Console Support Fixing Plate (99). Secure the Console (107) to Console Support Tube (12) with two M6 x 50mm Bolt (111). 99 99 5 5 107 12 13 14 111 111 SMOOTH 6.25 MOTORIZED TREADMILL Visit us at: 12 ASSEMBLY STEP 3: Connect the Upper Section Computer Wire (7) to the Lower Section 7 Pin Control Wire (24) and the Upper Section Safety Key Wire (78) to the Lower Section Safety Key Wire (52). Insert any extra cable length into the Left Upright (13). Insert the Left and Right Uprights (13 and 14) into the Base Frame (36) and secure by tightening the two Bolts (105) as shown in FIG 2. The two Bolts (105) are preassembled to the Base Frame (36) at the factory. 36 14 13 36 105 D D 14 36 13 52 24 78 7 105 SMOOTH 6.25 MOTORIZED TREADMILL Visit us at: 13 ASSEMBLY STEP 4: Insert the Water Bottle Holder (108) into Console (106). 106 108 SMOOTH 6.25 MOTORIZED TREADMILL Visit us at: 14 ASSEMBLY STEP 5: Slide the Handlebar Cover – Left #2 (18) and Handlebar Cover – Right #1 (19) onto the Cross Brace (16) as shown. Attach the Cross Brace (16) to the Left Upright (13) and Right Upright (14) using M8 x 80mm Allen Bolt (103). Do not fully tighten the M8 x 110mm Allen Bolt (103) at this time. 13 14 18 19 16 16 18 103 103 SMOOTH 6.25 MOTORIZED TREADMILL Visit us at: www.smoot...