Votes - , Average rating:
(
)
)
Manafacture: Image
File size: 1.6 mb
File name:
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
Before reading further, please familiarize yourself with the parts that are labeled in the drawing below. BEFORE YOU BEGIN Handrail Console Console Latch Storage Latch Book Holder Key/Clip Circuit Breaker Walking Belt On/Off Switch Foot Grip Rear Roller Adjustment Bolts Pulse Sensor RIGHT SIDE LEFT SIDE 5 ASSEMBLY Assembly requires two people. Set the treadmill in a cleared area. Do not remove the packing material from the area shown in drawing 2. Remove all other packing materials. Do not dispose of the packing materials until assembly is completed. Treadmill assembly requires the included allen wrench your own phillips screw driver and 9/16” wrench Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. 1. See drawing 2. Leave in place the packing material shown in the indicated area until step 1 is completed. While a second person holds one end of the treadmill, carefully tip the treadmill onto its side as shown. Using the included allen wrench and a 9/16” wrench, attach the two Extension Legs (70) to the base of the Uprights (109) with the four Bolts (71) and Nuts (68). Make sure that the Extension Legs are turned so the Base Pads (66) are in the positions shown. With the help of a second person, carefully raise the treadmill to the vertical position, and then lower the Walking Platform (93) to the floor. Note: If the treadmill rocks slightly, tip the treadmill back onto its side, loosen the four Nuts (68), adjust the positions of the Extension Legs (70), and then retighten the Nuts. Raise the treadmill back to the vertical position. Repeat until the rocking motion is eliminated. 2. Remove the packing material from the area shown. Attach the Storage Latch Assembly (33) and the Latch Spacer (35) to the left Upright (109) with two Latch Screws (34) as shown. Be careful not to overtighten the Latch Screws. Thread the Console Latch (55) into the right Upright (109). 3. Pull the Console Latch (55) to the right, and rotate the Console Base (43) to the position shown. Release the Console Latch, making sure that the Console Base is locked in place. Note: It may be helpful to push down on the right Handrail (39) and push the Console Latch into the locked position. Note: If the Handrail (39) rocks, attach one or two pieces of the included felt onto the bracket in the locations shown in drawing 2. 93 1 109 71 68 70 66 71 68 70 66 109 3334 35 Felt 2 109 55 Packing Material Felt 3 43 39 55 6 4a. Make sure that the treadmill is less than six feet away from the cabinet. Note: There are two ways to connect the treadmill to an outlet. First, the cabinet has a power cord that can be plugged into the treadmill and another power cord that can be plugged into an outlet using a surge suppressor. Second, the treadmill power cord can be plugged into the treadmill and into an outlet using a surge suppressor. To connect the treadmill using the cabinet power cord, follow the instructions in this step. To connect the treadmill using the treadmill power cord, see step 4b. Important: All references to power cords in other sections of this manual apply to both the cabinet power cord and the treadmill power cord. Feed the cabinet power cord and the cabinet audio wire through the looped Plastic Tie (76) at the front of the treadmill. Plug the power cord and the audio wire into the treadmill as shown. Tighten the Plastic Tie. (The Plastic Tie can also be released if needed.) 4b. Plug the Treadmill Power Cord (123) into the front of the treadmill as shown. 5. Locate the indicated wire on the back of the cabinet. Plug the wire into the connection panel. If you plan to use one or both of the power cords on the back of the cabinet, plug the power cords into appropriate outlets using surge suppressors as described on page 8. 6. Make sure that all parts are properly tightened before you use the treadmill. Note: If there is a thin sheet of clear plastic on the console decal, remove it. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 24). To protect the floor or carpet from damage, place a mat under the treadmill. Cabinet Power Cord 123 4b 5 4a 76 Cabinet Audio Wire Wire Power Cord Power Cord Connection Panel 7 OPERATION AND ADJUSTMENT THE PERFORMANT LUBETM WALKING BELT Your treadmill features a walking belt coated with PERFORMANT LUBETM, a high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear. HOW TO PLUG IN THE POWER CORD DANGER: Improper connection of the equipment-grounding con...
Other models in this manual:Fitness Equipment - HGTL09110C (1.6 mb)
Fitness Equipment - HGTL09110M (1.6 mb)