2 Required Tools .................................................................... 2 Attach the Feet and Foot Covers ......................................... 3 Attach the Bottle Holder/Accessory Tray ........................... 6 Assemble the Shroud ......................................................... 7 Disassemble the Equipment............................................. 12 Getting Started Note: Assemble the weight stack shroud and bottle holder/accessory tray after the equipment is positioned in the facility. Assembly takes about 15 minutes to complete. If this is the first time you have assembled this type of equipment, allow more time. Open the Box Open the box and remove the packing materials. Before you begin installing the weight stack shroud assembly, verify that you have received the following parts: For Weight Stack Shroud Assembly .. One front shroud assembly (CW34005) .. One pulley cover (CW34012) .. One lower left corner cover (CW34343) .. One lower right corner cover (CW34343) .. One pulley plug cover (CW34013) .. One lower middle cover (CW33945) .. One lower back cover (CW33944) .. One upper back cover (CW34375) .. One top cover (CW33947) .. One adjustable foot (CW39916-102) .. One foot cover with 75-degree upper opening (front, CW34061-103; back, CW34061-104) .. Two #8 x 1...” Phillips-head self-tapping screws .. Ten ...”- 20 buttonhead screws .. Two #8 x .." Phillips-head self-tapping screws For Attaching Bottle Holder/Accessory Tray .. One bottle holder/accessory tray (CW34368) .. One U-shaped bottle holder bracket (CW34364) .. Two #8 - 32 machine screws .. Two custom bolts .. Two lock washers .. Two flat washers .. Two ..” - 16 low head bolts Required Tools .. One ...” hex key .. One ...” hex key .. One ..” hex key .. One ....” socket wrench .. One ...” open-end or box-end wrench .. One 1” open-end or box-end wrench .. One #2 Phillips screwdriver Caution: Do not use power tools to tighten screws attaching the weight stack shroud components. Using power tools may void the Precor warranty. Attach the Feet and Foot Covers To Attach the Adjustable Foot: 1. Align the adjustable foot with the hole built into the cylindrical leg. 2. Screw the adjustable foot into the leg until the machine sits level on the floor. Caution: To prevent damage to the adjustable foot, screw it all the way into the frame before moving equipment. Figure 1: Adjustable foot attachment The following graphic shows the location of the adjustable foot. Figure 2: Adjustable foot and foot cover attachment locations To Attach the Foot Covers: Note: When you install each foot cover, no gap should appear between its front and back halves. Also, the opening in the top of the assembled foot cover should align with the angle of the frame leg attached to the foot. 1. Position the foot covers on either side of the equipment foot. 2. Attach the foot covers around the equipment foot using: Two #8 x 1...” Phillips head self-tapping screws Figure 3: Foot cover attachments Use this illustration to ensure that the foot covers are positioned and attached correctly. Figure 4: Foot cover positioning To Adjust the Stability Foot: The stability foot is located centrally underneath the weight stack frame and should rest evenly on the floor. If the foot is not resting firmly on the floor, perform the following procedure. Note: Adjustments to the stability foot must be completed before the shroud is attached. 1. Loosen the stability foot bolts using a 1” open-end or box wrench and a ...” socket wrench. 2. Pull the stability foot downward so that it rests firmly on the floor. 3. Tighten the stability foot bolts using tools from step one. Important: Once all foot adjustments are complete, gently rock the machine. If there is any movement, readjust the stability foot. Figure 5: Location of stability foot and mountings Attach the Bottle Holder/Accessory Tray To Attach the Bottle Holder/Accessory Tray to the Weight Tower Frame: 1. Locate the bottle holder/accessory tray. Snap the two pieces together and set them aside. Note: For this unit, the bottle holder/accessory tray attaches to the side of the front weight tower upright. 2. Place the bottle holder bracket upside down (curved side at the top) and attach it to the weight stack tower using: Two custom bolts Two lock washers Two flat washers Two ..” - 16 low head bolts One ...” hex key One 1" open-ended wrench Note: The custom bolts pass through the frame from the inside hole and align with the smaller hole on the outside of the frame. Figure 6: Bottle holder bracket attachment 3. Set the bottle holder/accessory tray on top of the bottle holder bracket and align it with the bracket screw holes. Attach it to the bracket using: Two #8 - 32 machine screws Note: Attach screws firmly, but do not overtighten. Figure 7: Bottle holder/accessory tray attachment Assemble the Shroud Before Beginning the Assembly All cables should be correctly seated and tensioned. Make any adjustments before you instal...