Votes - 6, Average rating: 4
(
)
)
|
manual abstract
Step 2 Remove the screw securing the SEAT SHROUD ASSEMBLY and remove the SEAT SHROUD ASSEMBLY from the frame. Step 3 Remove the eight screws securing the user right SHROUD. Rotate the user right crank arm to the 12:00 position, cover the crank arm with a cloth, and carefully remove the SHROUD from the frame. NOTE: BE CAREFUL NOT TO DAMAGE THE SHROUD WHEN MANEUVERING IT AROUND THE PEDAL AND CRANK SHAFT. 1“ User Left CABLE ASSEMBLY beneath the angled frame member and out the bottom front of the bike behind the FRONT SHROUD BRACKET. Cable Clamp Step 8 Place one ADHESIVE BACKED CABLE CLAMP 1” down from the top ridge of the user left shroud and 1/2” from the inner edge. Position the CABLE CLAMP with the opening facing the inner edge of the user left shroud. (Figure 2) Step 9 Place another ADHESIVE BACKED CABLE CLAMP at the bottom front edge of the user left shroud. Position the clamp with the opening facing the outside of the bike. Step 10 Insert the FITNESS ENTERTAINMENT CABLE ASSEMBLY into the top cable clamp Shroud leaving a 20” length extending from the top CABLE CLAMP. Figure 2 Step 4 Remove the nuts and washers from the ALTERNATOR TERMINALS “B” and “E”. Place the red wire RING TERMINAL (large) of the FITNESS ENTERTAINMENT CABLE ASSEMBLY over ALTERNATOR TERMINAL “B” and secure the connector with the appropriate nut and washer. Place the orange wire RING TERMINAL of the FITNESS ENTERTAINMENT CABLE ASSEMBLY over ALTERNATOR TERMINAL “E” and secure the RING TERMINAL with the remaining nut and washer. Tighten nuts to 25 - 30 in. lbs. NOTE: DO NOT REMOVE THE EXISTING RING TERMINALS FROM THE ALTERNATOR STUDS. NOTE: TO AVOID POTENTIAL DAMAGE, BE SURE THE RING TERMINALS OF THE FITNESS ENTERTAINMENT CABLE ASSEMBLY FACE THE CENTER OF THE ALTERNATOR. Cable AssemblyFront Shroud (Bundle Excess) Bracket Step 5 Route the FITNESS ENTERTAINMENT CABLE ASSEMBLY along the existing wire cluster and secure it near the existing wire tie with a supplied wire tie. NOTE: BE SURE TO LEAVE ADEQUATE STRAIN RELIEF OF THE FITNESS ENTERTAINMENT CABLE ASSEMBLY AT THE ALTERNATOR. Step 6 Route the FITNESS ENTERTAINMENT CABLE ASSEMBLY along the top of the ALTERNATOR MOUNTING BRACKET and secure with a supplied wire tie. (Figure 1) Step 7 Feed the FITNESS ENTERTAINMENT NOTE: WITH A SUPPLIED ALCOHOL WIPE, CLEAN THE SHROUD AT EACH CABLE CLAMP LOCATION BEFORE MOUNTING THE CABLE CLAMPS. Terminal “B” Terminal “E” Front Shroud Opening Alternator Mounting Bracket Figure 1 Terminal “B” Terminal “E” Life Fitness Models 9500HR / 9100 Exercise Bikes Fitness Entertainment Kit Installation (Continued) Step 11 Run the FITNESS ENTERTAINMENT CABLE ASSEMBLY down the front of the user left shroud making certain the FITNESS ENTERTAINMENT CABLE ASSEMBLY lays flat against the shroud. Insert the FITNESS ENTERTAINMENT CABLE ASSEMBLY into the bottom CABLE CLAMP. Step 12 Place a third CABLE CLAMP on the underside of the user left shroud front as close to the frame as possible (approximately 1” from the frame). Pull the excess FITNESS ENTERTAINMENT CABLE ASSEMBLY back into the bike until the FITNESS ENTERTAINMENT CABLE ASSEMBLY is tight against the user left shroud. Insert the FITNESS ENTERTAINMENT CABLE ASSEMBLY into the third cable clamp. Step 13 Bundle the excess FITNESS ENTERTAINMENT CABLE ASSEMBLY as shown in Figure 1 and secure with a supplied wire tie. Secure the bundled FITNESS ENTERTAINMENT CABLE ASSEMBLY to the frame away from moving parts as shown with another supplied cable tie. Step 14 Apply two CABLE CLAMPS to the front of the user left shroud in-line and between the two previously installed CABLE CLAMPS alternating the direction of the cable clamp openings. Insert the FITNESS ENTERTAINMENT CABLE ASSEMBLY into the CABLE CLAMPS. Step 15 Reverse steps 1 through 3 to return all shroud parts to their proper positions. Tighten screws to 12 - 15 in. lbs. Step 16 Model 9500HR: Apply a CABLE CLAMP approximately 3” down from the bend in the user left NECK SHROUD and approximately 1/4” from the NECK SHROUD OVERLAP JOINT. Position the CLAMP with the opening facing the NECK SHROUD OVERLAP JOINT. Continue routing the FITNESS ENTERTAINMENT CABLE ASSEMBLY upwards flat against the shroud and insert the FITNESS DisplayENTERTAINMENT CABLE ASSEMBLY into the CABLE CLAMP. Console Model 9100: Apply a CABLE CLAMP approximately 1/2 way up the handlebar vertical tube. Continue routing the FITNESS ENTERTAINMENT CABLE ASSEMBLY upwards flat against the handlebar vertical tube and insert the FITNESS ENTERTAINMENT CABLE ASSEMBLY into the CABLE CLAMP. Receiver Step 17 (Cardio Theater Wireless System Only) Cable Assembly NOTE: WITH A SUPPLIED ALCOHOL WIPE, CLEAN THE SHROUD AT EACH HOOK AND LOOP FASTENING STRIP LOCATION BEFORE MOUNTING THE HOOK AND LOOP FASTENING STRIPS. Cable Remove the four screws and mounting block from the back of the FITNESS Clamp ENTERTAINMENT RECEIVER. Remove the backing on one side of the hook and User Left loop fastening strips provided and apply lengthwise to the...