Votes - 4, Average rating: 3.5
(
)
)
|
manual abstract
MILLIMETERS 0 10 20 30 40 50 60 70 80 90 100 hardware 8 Screw M4 x 19mm (4 pieces) 55 Screw #8 x 19mm (4 pieces) 16 Screw M6 x 20mm (2 pieces) 17 Screw M8 x 15mm (4 pieces) 121 Screw M8 x 19mm (4 pieces) 40 Metal Cap (2 pieces) Allen Wrench (1 piece) Wrench (1 piece) Wrench (1 piece) Wrench (1 piece) 130 Screw M6 x 15mm (2 pieces) 46 Bolt M8 x 78mm (2 pieces) 4 Safety Key (1 piece) Step 1: Remove your EVO 1CD Treadmill from the carton and place it on the floor in an open area as shown in FIG-1. Raise the Right and Left Handle Uprights (6 and 7) to the upright position and secure with Screws (17). assembly instructions -6- ASSEMBLY FIG-1 assembly instructions -7- Step 2: Remove the Screw (51) then rotate the Computer Support (3) up to the correct position as shown and secure with the Screw (51). ASSEMBLY Step 3: Rotate the Console (39) up to its proper angle and secure with Screws (16) as shown in FIG-2. ASSEMBLY assembly instructions -8- FIG-2 Step 4: NOTE: If you have the Optional Smooth Music Package follow these instructions before attaching the Console Tray (137). Run the Cd Player Wires from the back of the Console (39) first through the small hole on the Console Tray (137), then through the tabs on the back of the Console Tray (137) and finally through the small hole on the side of the Console (39) as shown. Attach Console Tray Bracket (134) to the Console Tray (137) and secure with Screws (135). Attach the Console Tray (137). Insert the Console Tray Bracket (134) into the Console (39) and secure with the Screw (133). NOTE: For proper use please make sure to insert the plastic flange UNDER the metal tab before inserting the screw. assembly instructions -9- ASSEMBLY CD PLAYER WIRES Plastic Flange Step 5: Attach the Cross Tube (45) to the Left and Right Handle Uprights (6 and 7) and secure with the Metal Cap (40) and Bolts (46). Secure the Computer Support (3) to the Right and Left Handle Uprights (6 and 7) by tightening the Screws (18). ASSEMBLY assembly instructions -10- ASSEMBL Y Step 6: Unscrew Bolt (132). Insert the Console Tray Support Tube (138) into the Cross Tube (45) and secure with Bolt (132). Do not fully tighten until later. assembly -11 assembly instructions ASSEMBLY Step 7: Rotate the Console Tray Support Tube (138) and slide it into the hole underneath the Console Tray (137). -12 Step 8: Fully tighten Screws (18) and (51) and Bolts (46) and (132) at this time. assembly instructions -13- ASSEMBLY assembly instructions -14- Step 9: Connect the Motion Control Sensor and Hand Pulse Sensor wires then attach the Right and Left Handlebars (30 and 12) to the Right and Left Handle Uprights (6 and 7) and secure using Screws (121). ASSEMBLY Connect the sensor wires Connect the sensor wires Connect the sensor wires Step 10: Mount the Handle Cover Right - 1 (42) and the Handle Cover Right - 2 (44) to the Right Handle Upright (6) and secure with Screws (55) and (8). Mount the Handle Cover Left - 1 (43) and the Handle Cover Left - 2 (41) to the Left Handle Upright (7) and secure with Screws (55) and (8). ASSEMBLY assembly instructions -15- Step 11: Attach the Base Frame End Caps (14) to the Left and Right Handle Upright (6 and 7) and secure using the Screws (130). ASSEMBLY assembly instructions -16- -17- assembly instructions Connecting the Speakers and CD Player: When connecting the Speakers to the Console first plug the Speaker Wires into the sides of the Console. Then insert the Speakers into the sides of the Console and secure with Knobs. Plug the two wires from the Console Tray into the CD Player then place it on the Tray as shown in FIG 3. NOTE: There are three plugs located on the left side of the CD player. The rear plug is the AC power. The middle plug (Line Out) is not used at all. Leave that one open. The front plug is called Headphones Out and is used for the speakers (or headphones if you like). Warning: On the right side of the CD Player there is a button called “Hold”. This button should ALWAYS be set to OFF. If it is on, the unit will not play. OPTIONAL EQUIPMENT ASSEMBLY FIG-3 CD Player Console Tray Speaker Speaker Console Knob Knob AC Power Line Out (not used) CD Player, left side Headphones Out CD Player, right side -18- folding instructions Your treadmill can be folded up for space saving storage. To do this first be sure that the deck is at the lowest incline level. Simply lift the deck up from the rear of the treadmill and fold up until it locks in place. TO PREVENT INJURY BE SURE YOU HAVE A FIRM HOLD WHEN RAISING THE DECK. You will hear a “click” sound as the lock engages. FOLD UP FOR STORAGE 2. Raise the deck up until the lock engages. 1. Stand behind the treadmill and lift the deck up. CLICK -19- roll away instructions How to roll away the EVO 1CD Treadmill: After folding the treadmill tilt it to one side (you may need the help of a friend), reach under the Base Frame (1) and pull down the Caster Bracket (49). Repeat this procedure on the other side. Then to roll away for stora...