Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
EVO FX2 MOTORIZED TREADMILL Visit us at: 10 ASSEMBLY STEP 1: Remove your treadmill from the carton and place it on the floor in an open area as shown in FIG1. Raise the Left Upright (14) and secure with Bolts (77 and 76) and Washers (73 and 89). Repeat this step for the Right Upright (13). DO NOT FULLY TIGHTEN AT THIS POINT. EVO FX2 MOTORIZED TREADMILL 11 EVO FX2 MOTORIZED TREADMILL 11 ASSEMBLY STEP 2: Attach the Left Handlebar (24) and Right Handlebar (23) using Bolt (77) and Washer (73). Attach the Plastic Cover (80) to the bottom of the Left Upright (24) and Right Upright (23) using Screw (29). Visit us at: EVO FX2 MOTORIZED TREADMILL Visit us at: 12 ASSEMBLY STEP 3: Rotate the Console Support (28) and secure with the Console Support Locating Screw (101). Rotate the Console (26) and secure with Screws (88). Screws (88) are already pre-assembled (please refer to the exploded diagram). Attach the Right Handlebar Front End Caps (95 and 97) to the Right Handlebar (23) and secure using Screws (87 and 81). Repeat the same procedure for the Left Front End Caps (94 and 96). EVO FX2 MOTORIZED TREADMILL 13 EVO FX2 MOTORIZED TREADMILL 13 ASSEMBLY STEP 4: Attach the Reading Rack (27) to the Console (26) and secure with Screws (99). Fully tighten all nuts and bolts. Your treadmill is now fully assembled. Visit us at: EVO FX2 MOTORIZED TREADMILL Visit us at: 14 FOLDING INSTRUCTIONS FOLDING INSTRUCTIONS: IMPORTANT: Make sure the Treadmill is in its lowest position of Elevation. If not the treadmill will not fold. To fold your treadmill stand at the rear of the treadmill and lift the deck up until a click can be heard. This is the locking mechanism engaging. EVO FX2 MOTORIZED TREADMILL Visit us at: 15 UNFOLDING INSTRUCTIONS UNFOLDING INSTRUCTIONS: To unfold the treadmill for use stand at the rear of the treadmill and use your left foot to press on the locking mechanism (69). Lower the treadmill running deck until the rear wheels touch the floor. NOTE: Never stand on the locking mechanism without supporting the deck, as the deck will drop. EVO FX2 MOTORIZED TREADMILL Visit us at: 16 LEVEL ADJUSTMENT LEVEL ADJUSTMENT: Uneven flooring could cause the spring loaded lock pins not to engage and prevent the treadmill from either folding or inclining. To adjust the level follow the instructions below. You will need someone to help with this, as it involves lifting the treadmill. 1. Fold the treadmill up by following the folding instructions. 2. Tip the treadmill to the Left. You will then see the level adjusters. These will need to be screwed either in or out to level the treadmill. Repeat for the other side. 3. Unfold the treadmill as per the Unfolding instructions. EVO FX2 MOTORIZED TREADMILL 17 EVO FX2 MOTORIZED TREADMILL 17 MAINTENANCE HOW TO MAINTAIN THE EVO FX2 TREADMILL: Proper maintenance is very important to ensure your treadmill is always in top working condition. Improper maintenance could cause damage or shorten the life of your treadmill and exceed the LIMITED WARRANTY coverage. ?? Important: Never use abrasives or solvents to clean the treadmill. To prevent damage to the computer, keep liquids away and keep it out of direct sunlight. ?? Inspect and tighten all parts of the treadmill regularly. Replace any worn parts immediately. BELT ADJUSTMENT: Belt adjustment and tension performs two functions: adjustment for tension and centering. The running belt has been adjusted properly at the factory. However transportation, uneven flooring or other unpredicted reasons could cause the belt to shift off center resulting in the belt rubbing with the plastic side rail or end caps and possibly causing damage. To adjust the belt back to it’s proper position please follow the directions below: ?? Walking belt has shifted to the left: First unplug the power cord from the surge protector. Using the hex key provided, turn the left rear roller adjustment bolt 1/4 turn in the clockwise direction. Plug the power cord back into the surge protector and run the treadmill at 2.5 mph. You should see the belt start to correct itself, moving back towards the center. Repeat the above procedure until the walking belt is centered. It may be necessary to set walking belt tension once you have completed this procedure if the belt feels like it is slipping while walking. Refer below to the "Walking belt slipping" instructions. ?? Walking belt has shifted to the right: First unplug the power cord from the surge protector. Using the hex key provided, turn the right rear roller adjustment bolt 1/4 turn in the clockwise direction. Plug the power cord back into the surge protector and run the treadmill at 2.5 mph. You should see the belt start to correct itself, moving back towards the center. Repeat the above procedure until the walking belt is centered. It may be necessary to set walking belt tension once you have compl...