Votes - 4, Average rating: 3.8
(
)
)
|
manual abstract
Make sure that the power cord is not plugged in. With the help of a second person, carefully tip the treadmill onto its left side. Partially fold the Frame (12) so that the treadmill will be more stable. Do not fully fold the treadmill until it is completely assembled. Attach the four Base Pads (97) to the bottom of the Base (82) with four 1” Tek Screws (115) (only two Base Pads and 1” Tek Screws are shown. 97 12 97 115 82 1 115 6 7 2. Identify the Right Upright (10). Note: The Left Upright (9) has the Latch Housing (77, see step 3) attached to it. Have a second person hold the Right Upright (10) near the Base (82) as shown. Orient the Right Upright so that it is angled forward (see step 3). Feed the Upright Wire Harness (17) into the lower end of the Right Upright and out of the upper end. Next, hold the Right Upright (10) against the Base (82). Be careful not to pinch the wires. Insert two 2 3/4” Bolts (47), with two Washers (29) and two Star Washers (81), into the Base, and loosely thread the Bolts into the lower end of the Right Upright (10). Attach a Wheel (95) to the Base (82) with a Wheel Bolt (86). Do not overtighten the Wheel Bolt; the Wheel must be able to turn freely. With the help of a second person, tip the treadmill onto its right side. Be careful not to damage the Upright Wire Harness (17). Have a second person hold the Left Upright (9) near the Base (82). Orient the Left Upright so that it is angled forward (see step 3). Attach the Left Upright and the other Wheel (not shown) as described above. Note: There are no wires in the Left Upright. 10 86 95 2 82 81 81 47 29 47 29 9 3. With the help of a second person, set the treadmill on the floor with the Left and Right Uprights (9, 10) vertical. Identify the Right Handrail (124), which has a large hole in the left side. Feed the Wire Harness (17) up through the hole in the bottom of the Right Handrail and out of the large hole in the left side. Note: It may be helpful to use needlenose pliers to pull the Wire Harness out of the large hole. Set the Right Handrail (124) on the Right Upright (10). Finger tighten a 4” Bolt (120) through the Right Upright into the lower end of the Right Handrail. Attach the upper end of the Right Handrail with a 2 1/2” Bolt (56). Do not tighten the Bolts yet. Attach the Left Handrail (123) as described above. Note: There is not a wire in the Left Handrail. 9 124 10 123 77 17 Large Hole 120 56 120 56 3 17 8 6. Have a second person hold the Console (78) near the Right Upright (10). Attach the ground wire from the Console to the Right Upright with the 1/2” Silver Screw (107). Connect the Upright Wire Harness (17) to the wire harness on the Console (78). Make sure to connect the connectors properly (see the inset drawing). The connectors should slide together easily and snap into place. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Insert the connectors into the Console. 107 17 10 6 78 Ground Wire 17 5. Attach the Weight Rack (125) to the brackets on the Left and Right Uprights (9, 10) with four Weight Rack Bolts (121) and four Nuts (122). Attach all of the Weight Rack Bolts and Nuts before tightening any of them. Firmly tighten the four 2 1/2” Bolts (56). Next, firmly tighten the two 4” Bolts (120). 121 56 56 121 122 120 122 125 9 10 5 120 4. Hold the Crossbar (88) between the Handrails (123, 124). Make sure that the square hole in the Crossbar is on top as shown. Attach the Crossbar with two 2 1/2” Bolts (56). Do not tighten the Crossbar Bolts yet. 123 124 56 Square 56 Hole 88 4 7. Set the Console (78) on the Left and Right Uprights (9, 10). Be careful not to pinch any wires. See drawing 6 on page 8. Make sure that the Upright Wire Harness (17) is not in the small cutout shown by the arrow. Using the included 90° screwdriver and a phillips screwdriver, attach the Console (78) to the Uprights (9, 10) and the Crossbar (88) with six 3/4” Screws (39). Start all six Screws before tightening any of them; be careful not to overtighten the Screws. 8. Lower the Uprights (9, 10) until the handrails are touching the floor. See the lower drawing. Position the Uprights (9, 10) so that the treadmill Frame (12) is centered between the Uprights. Firmly tighten the four 2 3/4” Bolts (47). Then, raise the Uprights (9, 10) back to the vertical position. 9. Remove the knob from the pin. Make sure that the collar and the spring are on the pin as shown. Insert the pin into the Latch Housing (77), and tighten the knob back onto the pin. 10 39 7 78 88 9 39 39 8 9, 10 Handrail 47 10 9 12 Top View 9 9 Knob Pin Collar Spring 77 10. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may be included. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 24). To protect the floor or carpet, place a mat under the treadmill. 9 OPERATION AND ADJUSTMENT THE PERFORMANT LUBETM WALKING BELT Your t...