Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  
downloaded: 14   File size: 94 kb   Manafacture: Welch Allyn Medical Diagnostic Equipment  
Category: Shop Equipment
@name

Please consult factory for availability. & When included, the power pack is a wall mount device with 110 vac primary, and a regulated +5 VDC secondary output. + Connector contains a molded-in power jack. ^ Power must be supplied on pin 9 of the DB-9 connector. SCANTEAM 6980 User’s Guide 3 Installation All versions of the SCANTEAM 6980 depend on an external source of +5 VDC power to operate. Since most RS-232 interface ports don’t provide a power source, an external + 5 VDC power supply mu

downloaded: 13   File size: 106 kb   Manafacture: Welch Allyn Medical Diagnostic Equipment  
Category: Shop Equipment
@name

In Keyboard Programming mode, the MSR monitors the key pressed and programs the MSR depending on the keystrokes. The green LED will flash and the MSR will beep as each command key is typed during programming. In Keyboard Programming mode, the following parameters are programmable: • keystroke speed • keyboard type • transmit control character • prefix character selection • suffix character selection • beeper enable/disable • MSR track enable/disable • return to default settings The SCANTEA

downloaded: 6   File size: 315 kb   Manafacture: Welch Allyn Medical Diagnostic Equipment  
Category: Shop Equipment
@name

Worldwide Charging Information The battery pack is rated for 110/120 50/60 Hz applications but may be recharged worldwide using a step down transformer. The step down transformer, provided with each Cordless Scanner shipped outside North America, changes typical 240V AC into 120V AC output. All batteries shipped outside North America are fused to protect against charging at any higher voltage than 120V AC. Contact your distributor for more information or to order additional step down transformer

downloaded: 11   File size: 315 kb   Manafacture: Welch Allyn Medical Diagnostic Equipment  
Category: Shop Equipment
@name

Welch Allyn shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. This document contains proprietary information which is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of Welch Allyn, Incorporated. 1999 Welch Allyn, Inc. All

downloaded: 14   File size: 660 kb   Manafacture: Welch Allyn Medical Diagnostic Equipment  
Category: Shop Equipment
@name

The information in this publication does not represent a commitment on the part of Welch Allyn. Welch Allyn shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. This document contains proprietary information which is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into another lan

downloaded: 9   File size: 158 kb   Manafacture: Welch Allyn Medical Diagnostic Equipment  
Category: Shop Equipment
@name

Contact your Welch Allyn Sales Coordinator for the revision/model to fit your needs. The SAMPLE BAR CODES page (near the end of the programming menu) contains bar code symbols that you may use to verify that you have programmed your SCANTEAM 2380 correctly. Disclaimer Welch Allyn) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult Welch Allyn to determine whether any such changes h

downloaded: 18   File size: 401 kb   Manafacture: Welch Allyn Medical Diagnostic Equipment  
Category: Shop Equipment
@name

STEP 4. Determine the hex value from the Decimal to Hex to ASCII Conversion Chart (pg. 4–5) for the prefix or suffix you wish to enter. STEP 5. Scan the 2 digit hex value from the Programming Chart inside the back cover. . Repeat Steps 4 and 5 for every prefix or suffix character. . To add the Code I.D., scan 5, C, 8, 0. To add AIM I.D., scan 5, C, 8, 1. To add a backslash (\), scan 5, C, 5, C. STEP 6. Scan Save to exit and save, or scan Discard to exit without saving. Repeat Steps 1–6 to add a





Category