Login:
Votes - 1, Average rating: 3 ( )

User manual Sharp, model TCADH2556RCZZ

Manafacture: Sharp
File size: 470.58 kb
File name: aa7d8c24-a872-414b-94ea-c9ec58cdc33f.pdf
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


Before you set up the cash register, prepare three new alkaline batteries LR6 ("AA" size) which are necessary for memory backup. Find a stable and flat surface not subject to direct radiation, to place the cash register. English 1 Initializing the Cash Register To ensure the cash register operates properly, please use the following procedure: 1. Make sure the power cord is unplugged and batteries are not installed on the register. 2. Insert the manager (MA) key into the mode switch and turn it to the REG position. 3. Insert the plug of the power cord into the AC outlet. The buzzer will sound three times. IMPORTANT: This operation must be performed without batteries installed. 4. The cash register has now been initialized. The register display will show “0.00” with “ ”. 2 Installing the Batteries 1. Push the printer cover forward and detach it. 2. Open the battery compartment cover next to the paper roll cradle. 3. Install three new alkaline batteries LR6 (“AA” size) as shown at the right. (Batteries are not supplied with the cash register.) Make sure that positive (+) and negative (–) poles of each battery are properly oriented. 4. When the batteries are properly installed, “ ” on the display will disappear. Close the battery compartment cover. 3 Installing the Paper Roll (for receipt printing) If you want to use a paper roll for journal printing, please refer to GETTING STARTED section of the instruction manual. 1. Lift up the print roller release lever to unlock and open the print roller arm. 2. Set a paper roll in the paper roll cradle as illustrated right. NOTE: When setting a new paper roll in the paper roll cradle, be sure to cut the paper end behind the taped (or pasted) point in advance. 3. Feed the end of the paper along with the paper positioning guides as illustrated at the right. 4. While holding down the paper, slowly close the print roller arm, and push down the arm until you hear a click locking the arm. Make sure you securely push down the center of the wing part of the arm as illustrated at the right. The paper will be fed automatically. 5. Cut off the excess paper using the edge of the inner cover, and replace the printer cover. Press the Fkey to make sure the paper end comes out of the printer cover and clean paper appears. NOTE: If the print roller arm is not securely locked, the unit will not print correctly. If this problem occurs, open the arm, and close the arm as instructed above. REG OPX/Z MGR PGM X1/Z1 X2/Z2 OFF VOID MA Print roller arm Print roller release lever To the printer Incorrect To the printer Correct Paper positioning guides 4 Basic Programming Set the mode switch to the PGM position. Setting the Date Enter the date in 8 digits using the month-day-year format. Then press s. Example: 02262010s Date (February 26, 2010) Setting the Time Enter the time in 4 digits (“hhmm” format) using the 24 hour system. Then press s. Example: 1430s Time (2:30 p.m.) Setting Tax Rates (%) NOTE: If you are in an area that uses a tax table for tax calculation, please refer to the programming section in the instruction manual. Specify a tax rate (%) for calculation of tax on each taxable subtotal using the following sequence: s. 9. @. Tax number (1 to 4)* . @. Tax rate (0.0000% to 100.0000%) . @ . Minimum taxable amount (0.01 to 999.99) . s. A (Smallest amount for which tax must be collected.) *Up to 4 types of tax are programmable. Example1: Set state tax 6.25% with tax exempt as 12. s9@...

Other models in this manual:
Shop Equipment - XE-A206 (470.58 kb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category