OWNER’SMANUALOWNER’S MANUAL OPTIONAL HUMIDITY MODULEOPTIONAL HUMIDITY MODULE Accepts theAccepts the COMMERCIALCOMMERCIAL THERMOSTATTHERMOSTAT P/NP/N 33CS4500133CS450 01 AUTO I2:00 Su Pm HEAT COOL 72 74 Carrier Carrier CAUTION Follow the Installation Instructions before proceeding. Set the thermostat mode to “OFF” prior to changing settings in setup or restoring Factory Defaults. CAUTION NEVER PUT MORE THAN ONE JUMPER ON THE SAME MISC JUMPER BLOCK! THIS MAY DAMAGE YOUR THERMOSTAT. MISC3 OK MISC3
OWNER’SMANUALOWNER’S MANUAL OPTIONAL HUMIDITY MODULEOPTIONAL HUMIDITY MODULE Accepts theAccepts the COMMERCIALCOMMERCIAL THERMOSTATTHERMOSTAT P/NP/N 33CS4000133CS400 01 AUTO I2:00 Su Pm HEAT COOL 72 74HEAT COOL& CAUTION Follow the Installation Instructions before proceeding. Set the thermostat mode to “OFF” prior to changing settings in setup or restoring Factory Defaults. CAUTION NEVER PUT MORE THAN ONE JUMPER ON THE SAME MISC JUMPER BLOCK! THIS MAY DAMAGE YOUR THERMOSTAT. OK MISC3 MISC3 NOTE:
Route wires through large hole in Equipment Control Module. Level Equipment Control Module against wall (for aesthetic value only . Equipment Control Module need not be leveled for proper operation) and mark wall through 4 mounting holes. To avoid unintended bending of wall plate plastic, use all 4 screws and anchors. 2. Drill four 3/16.in. mounting holes in wall where marked. Thermostat may be mounted to a standard junction box if desired. Hole pattern on Equipment Control Module matches juncti
US patents: US7287709 B2, US20080147242 A1, USD582800 SI, US20060165149 A1, US6956463 B2. TABLE OF CONTENTS PAGE SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 INSTALLATION CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
It serves to impose the cycles per hour limits. It can be defeated for one cycle by simultaneously pressing the FAN and UP buttons. 41 Ten.Minute Staging Timer In multistage heating or cooling, this timer prevents any higher stage from turning on until preceding stage has been on for 10 minutes. When staging between compressor and electric heat or between compressor and furnace heat, the time is configurable. The timer is configurable via Option 17. This timer is overridden if temperature error
When the keypad lock selection is turned on, the padlock icon will be displayed. To unlock the keypad, press and hold the UP/DOWN buttons simultaneously for five seconds. When the keypad is unlocked, the padlock icon will turn off. The keypad will remain unlocked for two minutes after the last button press. After two minutes with no button presses, the keypad will lock again. The keypad will not lock in the software configuration mode or in the installer test mode. Default is OF (off). 31 Option
S 7310 W. Morris St. S Indianapolis, IN 46231 Printed in U.S.A. Edition Date: 05/09 Catalog No: TB--PAC-- 7SI Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. Replaces: TB--PAC-- 6SI 4 TB---PACTB---PHPBaseSeriesProgrammableThermostatsTB---PACTB---PHPBaseSeriesProgrammableThermostats Homeowner’s Guide Designed and Assembled in the USA. A07107 Base Series Programmable Thermostat SETTING TIME AND DAY At Power Up When power is
See Warranty Conditions below. ** If properly transferred within 90 days, otherwise 5 years. See Warranty Conditions below. In California and Quebec and other jurisdictions that pro hibit warranty benefits conditioned on registration, registration is not required for a transfer and all warranty periods for subsequent owners are five years from original installation. *** Applies only to Thermostats. Active electronic finished good accessories, such as the optional ExP module, have different warra
Only one can be selected. Table 2: Terminals for six wires 2 heat/1 cool system (RAK148P1 only) Note: Connect G terminal of thermostat to Zoneline Gl terminal for low fan speed or terminal Gh for high fan speed. Only one can be selected. Configuration mode. The configuration mode is used to set the RAK148P1 and RAK164P1 to match your heating/cooling system. These thermostats function with up to 2-stage heat pump systems (RAK148P1 only). To configure the RAK148P1 and RAK164P1, perform the followi
• Off is also used to access Setup AM and Program modes. Cool • In this mode, the thermostat controls the cooling system. • Press the Mode button to enter and exit the Program Cool mode. • In Program Cool mode (PROG displays), the thermostat will follow the program schedule that is stored in memory. Heat • In this mode, the thermostat controls the heating system. • Press the Mode button to enter/exit the Program Heat mode. • In Program Heat mode (PROG displays), the thermostat will follow the pr