Votes - 3, Average rating: 3.3
(
)
)
|
manual abstract
Certified to comply with ANSI A112.18.1M ASSE 1016 ROUGHING-IN DIMENSIONS Recommended Tools Flat Blade Screwdriver Phillips Screwdriver Remove as much surface dirt and film using clear water and soft cotton cloth (as described above). Use any of the following to remove tough surface film and build-up: Mild liquid detergents Clear ammonia free liquid glass cleaners Non-acidic, non-abrasive gentle liquid or fully dissolved powder cleansers mixed according to manufacturers directions. Non-abrasive liquid polishers Once clean, rinse faucet again with clear water to thoroughly remove cleaner or polish and blot dry with a soft cotton cloth. To keep your new faucet looking new, please follow these simple care instructions: DO: Simply rinse the faucet clean with clear water. Dry the faucet with a soft cotton cloth. DO NOT: Do not use any abrasive cleaners, cloths, or paper towels. Do not use any cleaning agents containing acids, polish abrasives, or harsh cleaners or soaps. Regular and routine cleaning will reduce the need for heavy cleaning and polishing. If heavy cleaning is required, the following procedures are recommended: CARE INSTRUCTIONS: Failure to follow these care instructions may damage the Faucet's finish. 200mm (7-7/8) 86mm (3-3/8) 34mm (1-3/8) 159mm (6-1/4) 150mm (5-7/8) 48mm to 68mm (2 to 2-5/8) R510 1/2 NPT R530 3/4 NPT R510 1/2 NPT R530 3/4 NPT 25mm (1) 1 3 5 2 4 M 9 6 8 9 8 3 TEMPERATURE CALIBRATION SET HOT LIMIT STOP 5 Check that arrow marking B points vertically upwards. If not, push the BLACK CLAMP (1) on the SECURING RING (2) to the right, pull off KNOB MOUNT (3) and reinstall KNOB MOUNT (3) with arrow "B" pointing upwards. For 100°F adjustment, turn the water supply on. Turn KNOB MOUNT (3) until the spout temperature is 100°F. Check that arrow marking A on the KNOB MOUNT (3) still points upward after adjusting the thermostat to 100°F. If not, pull out the RED LOCKING DEVICE (5). Remove KNOB MOUNT (3) without turning by sliding out as indicated by the arrow. Reinstall the KNOB MOUNT (3) so that the arrow marking A points upwards. The maximum mixed water temperature is set at 109°F at the factory. This setting can be changed if desired. Remove the TEMPERATURE LIMIT STOP (4) (H shaped Black Plastic part). Reinstall it at the desired notch as indicated in the diagram to limit the maximum mixed water temperature to 104°F or 112°F. Reinstall RED LOCKING DEVICE (5). ARROW "A" ARROW "B" 104 109 112 OPERATING THE VALVE 4 1 TRIM INSTALLATION 2 HANDLE INSTALLATION Align HANDLE (1) as shown and push onto KNOB MOUNT (2). Tighten HANDLE SCREW (3) with flat blade screwdriver. Push INDEX CAP (4) into HANDLE (2). Should the hot and cold water supply pipes have been transposed making adjustment impossible, proceed as follows: 3 TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION Remove check stops and re-install them transposed. Shut off water supply. Remove handle and rim CHECK STOP (RED TO BLUE) Important note: RED CHECK STOP is now on the right of the mixer body and the BLUE CHECK STOP is now on the left. Turn the water supply back on and perform the temperature adjustment in step 4. CHECK STOP (BLUE TO RED) Turn on water supply on and test installed fitting. If the system is delivering all Hot or all Cold and no mixed water the pipes are probably transposed. See step 3 for TRANSPOSED SUPPLY PIPING. Operate valve from off to cold to hot. Check temperature. If max mixed water temperature is to hot or to cold see step 4 and re-calibrate the valve. OFF COLD HOT Push CAP (1) over the O-RING SEAL (2). 1 1 3 Push ESCUTCHEON HOLDER (3) with lightly greased O-RING SEAL (4) over CAP (1). Attach with the two SCREWS (5) provided. Align pins in back of ESCUTCHEON (5) with holes in ESCUTCHEON HOLDER (3). Push ESCUTCHEON (5) flush against finished wall. PINS 2 2 3 5 4 GREASE ESCUTCHEON O-RING SEAL 4 M 9 6 8 9 8 3 ONE MODEL NUMBERS CHROME SATIN NICKEL 002 295 Replace the "YYY" with appropriate finish code CENTRAL THERMOSTAT LESS VOLUME CONTROL TRIM KIT M962631-YYY0A HANDLE SCREW AND INDEX BUTTON M908594-YYY0A HANDLE BASE M909438-YYY0A HANDLE INSERT US84045-0070A ESCUTCHEON SCREWS M907612-YYY0A ESCUTCHEON KIT M962630-0070A ESCUTCHEON HOLDER A907090-YYY0A CAP HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) 442-1902 Weekdays 8:00 a.m. to 6:00 p.m. EST IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST Product names listed herein are trademarks of American Standard Inc. © AS America, Inc. 2007 IN MEXICO 01-800-839-12-00 T064730 ...