Votes - 5, Average rating: 4.4
(
)
)
|
manual abstract
Use of any other lamp may damage the LCD projection TV. Before replacing the lamp, turn the power off on the main unit. Wait several minutes, then unplug the power cord. (The cooling fan will continue to blow for about two minutes after turning the power off.) Allow the lamp to cool down completely before removing it. The surface of the lamp remains extremely hot for at least 30 minutes after the power has been turned off. Sony XL-2100U or XL-2100 for KDF-WE655 series 1 Loosen the screws on the rear side panel. *The illustration described in right is for KDF-50WE655. 2 Remove the front panel. 3 Loosen the screw with a coin or similar object to remove the lamp cover. 4 Loosen the two screws that hold the lamp, then pull out the lamp. 5 Replace the new lamp and tighten the screws. 6 Reattach the lamp cover and tighten the screw. 7 Reattach the front panel securely. 8 Tightly screw the side panel in its place. Sony XL-2200 for KDF-WF655 series/KDF-XS955 series 1 Loosen the screws on the rear side panel. (only for WF655) 2 Remove the front panel. 3 Loosen the screw, release the bar (for WF655) or slide the knob to left (for XS955), and remove the lamp cover. 4 Loosen the screw that secure the lamp, then pull out the lamp. 5 Replace the new lamp and tighten the screw. 6 Reattach the lamp cover and tighten the screw. 7 Reattach the front panel securely. 8 Tightly screw the side panel in its place. (only for WF655) STD/DUO POWER PRO Additional Connections For best audio performance, connect your digital audio components using either digital optical or digital coaxial audio connections. Depending on which components are in your system, you may need to complete additional connections. For example, if you have a satellite receiver, you’ll need to connect the satellite antenna. If you have an A/V receiver, you’ll need to connect speakers. The connection diagrams shown in the reverse side are recommendations only; other possible solutions may exist. Connections that include an A/V receiver can often be very complex, so check your A/V receiver’s instruction manual for additional details. Activating CableCARD™ Service Before you can use CableCARD service, you need to insert the CableCARD (supplied by your cable provider) and activate the service, as described in right. Inserting the CableCARD incorrectly may result in permanent damage to the card and the TV. POWER TV/ DISPLAY VIDEO ENT TV F1 F2 GUIDE MENU TOP MENU FAVORITES FREEZE RESET SLEEP MTS/SAP JUMP ANT GUIDE VOL CH SAT/ CABLE FUNCTION DVD/VCR MUTING DVD/ VCR MODE SAT/ CABLE PICTURE WIDE TV /TV/SAT Connector type HDMI (High-Definition Multimedia Interface) Component video S VIDEO Composite video RF/Coaxial Making Video Connections Best Video Performance •See the “Cables Required” chart that appears with the diagram to determine which cables you’ll need. You may need to purchase extra accessories, such as cables and splitters, depending on the components you plan to connect. •Turn off and unplug all components before making connections. •If you are connecting a digital cable box, you’ll need a special bidirectional splitter that’s compatible with your cable box. Contact your cable provider for details. For these components See reverse side or or or or •Review the following chart to determine which diagram to use to connect the components in your system: KDF-42/50 WE655 KDF-55/60 WF655 KDF-55/60 XS955 Sony Corporation © 2004 Printed in U.S.A. 2-059-371-11(1) Quick Setup Guide Checking the Supplied Accessories Programming the Remote Control Connecting Your TV (See reverse side) Running Initial Setup Do not throw away this guide, and keep it handy for future reference. For further information, see the operating instructions supplied with the TV. Please follow the steps to setup your TV: 1 Running Initial Setup 2 Programming the Remote Control zzz Along with your new LCD projection TV, the packing box contains a remote control, two AA (R6) batteries and a Cleaning Cloth. These items are all you need to set up and use the TV. 1 Press POWER to turn on the TV. The Initial Setup screen appears. 2 Press V/v to select the on-screen display language. Then press . The message “Start auto program now?” appears. 3 Press V/v to select “Yes”, then press only. Initial Setup automatically creates a list of receivable channels. When finished, the lowest numbered channel is displayed. If you need to perform Auto Program again 1 Press MENU. 2 Press V/v to select (Channel), then press . 3 Press V/v to select “Auto Program,” then press . 4 Press . “Auto Program” appears and the TV starts scanning and presetting channels automatically. When all the receivable channels are stored, the “Show/Hide Channels” menu appears. Using this menu, you can start skipping unwanted channels (see “Selecting Channel Options” in the operating instructions). 5 Press MENU to exit the menu screen. Auto Program may take up to 50 minutes to complete. A progress bar will display the approximate progress of the Aut...