Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
NORMAL RECORDING OTR (One Touch Recording) You can ONLY watch the same TV program that is being recorded. 1 Select the channel to be recorded Press the number buttons on the CH 10 remote control or the CHANNEL K or L button. Remember: If the TV/VCR is connected to a cable box or satellite box, the TV/VCR must be on CH3 or CH4, then the channel to be recorded must be selected on the cable box or satellite box. 2 Select the tape speed Press the SPEED button to select the desired tape speed (SP/ SLP). SP REC 3 Begin recording Press the RECORD button. SP 4 Stop recording Press the STOP button when recording is completed. SKIPPING UNWANTED SCENES DURING RECORDING Press the PAUSE/STILL button to PAUSE temporarily stop recording. Press the PAUSE/STILL or RECORD button to resume recording. SP NOTE: • After five minutes, the TV/VCR will automatically switch to the Recording mode to prevent tape damage. This function enables you to set a recording length simply by pressing the REC/OTR button on the TV/VCR. Make sure ... • TV/VCR power must be turned on. • Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording.) NOTES: • This function CANNOT be done from the remote control. • Recording starts immediately when the REC/OTR button is pressed. • When the REC/OTR button is pressed 18 times, the TV/VCR returns to the Normal Recording mode. • To stop the OTR operation, press the STOP button on the TV/VCR or on the remote control. • To show the remaining time, press the DISPLAY button on the remote control so that “OTR” appears on the TV screen. (It will show up momentarily then disappear.) • Recording stops when 0:00 is reached. • Please note that in the SLP mode maximum recording time, assuming the tape is started at the beginning, is 8 hours using T-160 (or 6 hours using T-120). • If the tape runs out before the end time, the TV/VCR will switch to the Stop mode immediately, ejects the tape and turns itself off. 1 Select the channel to be recorded Press the number buttons on the remote control or the CHANNEL K or L button. Remember: If the TV/VCR is connected to a cable box or satellite box, the TV/VCR must be on CH3 or CH4, then the channel to be recorded is selected on the cable box or satellite box. 2 Select the tape speed Press the SPEED button to select the desired tape speed (SP/ SLP). - 19-EN 1A19 Avoid over lap of programs ... 3 Begin OTR OTR(2 : 30) There is a chance that a program will not be record- Press the REC/OTR button on the ed. when programs overlap; TV/VCR as many times as needed. • The program with an earlier start has priority. The recording length will be determined by the number of times you • Once the earliest program finishes, the overlapping press the REC/OTR button. Each SP programs will begin recording in sequence. additional push will increase the recording time by • The illustration below demonstrates the sequence 30 minutes. It is set up to 8 hours. of recordings. Push(es) Display Recording length 1 push (normal recording) 2 pushes 0:30 30 minutes 3 pushes 1:00 60 minutes 17 pushes 8:00 480 minutes 11:00AM 9:00AM 10:00AM 12:00PM TIMER RECORDING You may set the TV/VCR to start and end a recording while you are away. You can set 8 programs to record on specific days, daily or weekly within a 1 year period. In the example below, the timer is being set to record: DATE: July 6th, 2001 SETTING TIME: from 7:30PM to 8:50PM CHANNEL: CH61 TAPE SPEED: SP Make sure ... • If a cable box or satellite box is connected with the TV/VCR you will be limited to record only one channel. And the channel selector on the TV/VCR must be selected to the output channel of the boxes CH 3 or CH 4 and then the actual channel to be recorded must be selected on the boxes. • Clock must be set to the correct time and date before setting the timer. • TV/VCR power must be turn on to program it. • Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording.) • The channel you want to record is properly set in advance. Recording Sequence Program 1 10:00AM-11:00AM Program 2 9:00AM-10:00AM Program 3 9:30AM-12:00PM *Recording period is SHADED 1 Select “TIMER PROGRAMMING” Press the MENU button on the remote control. Confirm “TIMER PROGRAM – M E N U – B TIMER PROGRAMMING MING” is pointed by pressing the PICTURE CONTROL SETTING CLOCK CHANNEL SET UP USER’S SET UP LANGUAGE [ENGLISH] PLAY/K button. ZERO RETURN TIME SEARCH And press the F.FWD/B button. • If you have not yet set the clock, “MANUAL CLOCK SET” appears. If so, follow stops [3] to [8] on page 12. Then set the timer recording. 2 Select your desired program position (1~8) Press the PLAY/K or STOP/L button to select the desired program position. Then, press the F.FWD/B button. 3 Set the channel number Press the PLAY/K or STOP/L button until the desired channel number appears. (Exa...