Votes - 0, Average rating: 0
(
)
)
|
Other manuals for this model:
Televisions - LW22A13W (293.26 kb)
Televisions - LW22A13W (5.59 mb)
Televisions - LW22A13W (5.92 mb)
manual abstract
. Press Push Hold downImportant Note English-5 English-6 Control Panels . Using the Buttons on the Panel If the remote control no longer works or you have lost it, you can use controls on the panel of the TV to: Switch on the TV when it is in Standby mode and select channels ( C/P. ) Access the local menu ( MENU ) Adjust the volume (- +) Switch among Video input modes ( TV/VIDEO ) . POWER SWITCH . POWER INDICATOR . REMOTE CONTROL SENSOR . TV/VIDEO . MENU SELECTION . CHANNEL SELECTION . VOLUME ADJUSTMENT EN1-PD22EO 7/12/03 11:26 PM Page 6 EN1-PD22EO 7/12/03 11:26 PM Page 7 Connection Panels Rear of TV POWER INPUT CONNECTOR RCA AUDIO/VIDEO INPUT CONNECTORS S-VIDEO INPUT CONNECTOR WOOFER OUTPUTS ANTENNA INPUT CONNECTOR SCART 2 (VIDEO/AUDIO INPUT/OUTPUT) CONNECTOR SCART 1 (VIDEO/AUDIO INPUT/OUTPUT, RGB INPUT) CONNECTOR PC AUDIO INPUT CONNECTOR HEADPHONE CONNECTOR PC VIDEO INPUT CONNECTOR KENSINGTON LOCK (SEE PAGE 49) English-7 EN1-PD22EO 7/12/03 11:26 PM Page 8 Infrared Remote Control You can use the remote control up to a distance of about 23 feet from the TV. When using the remote, always point it directly at the TV. TELEVISION STANDBY BUTTON MODE : SELECTS A TARGET DEVICE TO CONTROLLED BY THE SAMSUNG REMOTE CONTROL (TV, VCR, CABLE BOX, OR DVD). NUMERIC BUTTONS ONE/TWO-DIGIT CHANNEL SELECTION SELECT TO THE PC MODE DIRECTLY SOUND STANDARD SELECTION VOLUME INCREASE TEMPORARY SOUND SWITCH OFF VOLUME DECREASE ON-SCREEN DISPLAY/ TELETEXT INDEX MENU ADJUSTMENT AND VIDEO OR DVD ADJUSTMENT BUTTON. moves or adjusts Menu. Adjusts the functions of Video or DVD. TELETEXT DISPLAY/MIX SOUND MODE SELECTION AUTOMATIC SWITCH-OFF PICTURE SIZE SELECTION PREVIOUS CHANNEL VIRTUAL DOLBY SELECTION PICTURE STANDARD SELECTION NEXT CHANNEL/ TELETEXT NEXT PAGE TV INFORMATION DISPLAY PREVIOUS CHANNEL/ TELETEXT PREVIOUS PAGE EXTERNAL INPUT SELECTION MENU EXIT TELETEXT LIST/FLOF MODE SELECTION STILL THE MAIN PICTURE/ TELETEXT CANCEL PIP FUNCTIONS; PIP ON/CHANNEL SELECTION / SIZE SETTING/SWAP/LOCATE/ INPUT SOURCE SELECTION(SOURCE)/ TELETEXT SUB-PAGE( ) . It is possible that the work of the transmitter is dull or not operated normally if the light of the Bulb is on around the TV set. English-8 EN1-PD22EO 7/12/03 11:26 PM Page 9 Connecting to an Aerial or Cable Television Network To view TV channels correctly, a signal must be received by the set from one of the following sources: An outdoor aerial A cable TV network A satellite network (see page 10 for further details) 1 In the first three cases, connect the aerial or network input cable to the 75. coaxial socket on the rear of the TV. 2 If you are using an indoor aerial, you may need to turn it when tuning your TV until you obtain a picture that is both sharp and clear. For further details, refer to: . “Automatic Storing of Channels” on page 16 . “Manual Storing of Channels” on page 18 . If you wish to subscribe to a cable network, contact your local dealer. or Cable Television Network Rear of the TV TV Antenna Connecting a non-AV-Link VCR You can connect a VCR to the TV using a: Coaxial cable SCART cable S-Video cable 1 Plug the aerial input cable into the appropriate socket on the VCR. 2 Connect a coaxial cable to the: VCR aerial output socket . Television aerial input socket 3 To obtain better picture quality and, in addition, simplify the setting up procedure of the VCR, you can connect a SCART cable between: . The AV (SCART) socket on the VCR and . A SCART socket on the rear of the TV 4 Follow the instructions supplied with your VCR to tune the VCR to your TV. ATT. M A IN FROM ANT. OUT TO TV DECODER AV TEST M A L G COUL N/B Rear of the TV Aerial output SCART cable Aerial input English-9 EN1-PD22EO 7/12/03 11:26 PM Page 10 Connecting a Satellite Receiver Rear of the TV Satellite Receiver or In order to watch TV programmes broadcast via a satellite network, you must connect a satellite receiver to the TV set. . If you wish to connect both a satellite receiver and a VCR, you should connect the: Receiver to the VCR VCR to the TV (see pages 41~42 for further details) Otherwise, connect the receiver directly to the TV. Using a SCART cable Connect the receiver SCART cable to one of the SCART connectors on the rear of the TV. Using a coaxial cable Connect a coaxial cable to the: Receiver output socket. Television aerial input socket. Connecting a Decoder Rear of the TV Decoder or In order to descramble a coded transmission signal, you must connect a decoder to the TV set. . If you wish to connect both a decoder and a VCR, you should connect the: Decoder to the VCR VCR to the TV (see pages 42~42 for further details) Otherwise, connect the decoder directly to the TV. Using a SCART cable Connect the receiver SCART cable to one of the SCART connectors on the rear of the TV. Using a coaxial cable Connect a coaxial cable to the: Receiver output socket. Television aerial input socket. English-10 EN1-PD22EO 7/12/03 11:26 PM Page 11 Connecting to a Sub-woofer Connect an audio cable...