Votes - 0, Average rating: 0
(
)
)
|
manual abstract
disconnect the USB storage device. Update the TV software Philips continuously tries to improve its products and we recommend that you update the TV software when updates are available. Check t for availability. Check the current software version 1 Press (Home). 2 Press to select [Setup] > [Software update] > [Current software]. » The TV displays the current software information. Change TV preferences 1 Press (Home). 2 Select [Setup] > [Installation] > [Preferences]. 3 Press OK or to enter [Preferences]. • [Location]Optimises TV settings for your location - home or shop. • [Volume bar]Displays the volume bar when adjusting the volume. • [EasyLink]Enables one-touch play and one-touch standby between EasyLink-compliant devices. • [Pixel Plus Link]Overrides the settings of connected devices and uses the settings of the TV. (Available only when [EasyLink] > [On] is selected). • [E-sticker]For shop mode only. Sets the location of the e-sticker. 4 Press to select your preference. 5 Press OK. 6 Press (Home) to exit. English EN 19 Access decoder channel You can map channels provided through a decoder or descrambler to your TV channel selection. In this way, you can select these channels by using the RC of your TV.The decoder or a descrambler must be connected to EXT1. Set decoder channel Map channels from a decoder or descrambler 1 Press (Home). 2 Select [Setup] > [Installation] > [Decoder]. 3 Press to enter [Decoder]. 4 Press to enter [Channel]. 5 Press to select channel number to map to the decoder/descrambler channel. 6 Press OK. 7 Press to select and enter [Status]. 8 Press to select the connector used by the decoder/descrambler ([None] or [EXT 1]). 9 Press OK. 10 Press (Home) to exit. Note • Select [None] if you do not want to map to the decoder/descrambler channel. Start a TV demo 1 Press DEMO on the remote control. 2 Press to select a demo and press OK to view it. 3 Press DEMO to exit. 20 EN Reset the TV to factory settings You can restore the default picture and sound settings of your TV. Channel installation settings remain the same. 1 Press (Home). 2 Select [Setup] > [Installation] > [Factory settings]. 3 Press OK or to enter the [Factory settings] menu. » [Reset] is highlighted. 4 Press OK to reset to factor y settings. 5 Press (Home) to exit. 6 Install channels The first time you set up your TV, you are prompted to select a menu language and to install TV and digital radio channels (if available). This chapter provides instructions on how to re-install and fine tune channels. Automatically install channels This section describes how to search and store channels automatically. Step 1 Select your menu language Note • Skip this step if your language settings are correct. 1 Press (Home). 2 Press to select [Setup] > [Installation] > [Language] > [Menu language]. 3 Press to enter [Menu language]. 4 Press to select a language setting and then OK to confirm. 5 Press (Home) to exit. Picture Sound Features Installation Software update Menu language Channel install. Preferences Decoder Factory setting Current software English Cesky Български Dansk Deutsch ........ Espanol Francais Step 2 Install Channels Select your countr y for proper channel installation. 12 Press Press (Home). to select [Setup] > [Installation] > [Channel install.] > [Channel assistant]. Picture Sound Features Installation Software update Menu language Channel install. Preferences Decoder Factory setting Current software Channel assistant Analogue: Manual 3 Press to select your country and then to go to the nex t step. Select your country Austria Belgium Croatia Czech Republic Denmark Finland France Germany 4 Select [Start] and press OK to re-install channels. Start automatic installation. This takes a few minutes. Start? » As the system searches for channels, you have the option to [Stop] the process. 5 To stop searching, select [Stop] and press OK. » A dialogue box appears asking you if you really want to [Stop] or [Continue] with the process. EN 21 English 6 Press to select [Stop] or [Continue]. 7 Press OK to confirm your choice. 8 When done, press (Home) to exit. Manually install channels This section describes how to search and store analogue TV channels manually. 1 Press (Home). 2 Press to select [Setup] > [Installation] > [Channel install.] > [Analogue: Manual]. » The [Analogue: Manual] menu appears. Picture Sound Features Installation Software update Menu language Channel install. Preferences Decoder Factory setting Current software Channel assistant Analogue: Manual 3 Press to select the item you want to adjust. • [System] • [Search] • [Fine-tune] • [Store cur. chan.] • [Store new channel] • [Skip channel] Step 1 Select your system Note • Skip this step if your system settings are correct. 1 Press (Home). 22 EN 2 Press to select [Setup] > [Installation] > [Channel install.] > [Analogue: Manual]. » The [Analogue: Manual] menu appears. 3 Press to select and enter [System]. 4 Press to select your country or region. ...