Votes - 4, Average rating: 4 ( )

Manafacture: Samsung File size: 25.25 mb File name: Language of manual:

Other manuals for this model:

Televisions - PS-42P2ST (293.26 kb)

Televisions - PS-42P2ST (4.14 mb)

Televisions - PS-42P2ST (4.62 mb)

Televisions - PS-42P2ST (3.55 mb)

d) PC Input Connect a PC signal from an PC. e) SCART Input Connect a audio, video, or RGB signal from external sources like VCRs or DVD players. (Signal Output does not operate). f) Audio Inputs (Video/PC) Connect a audio signal from external sources like VCRs or PC. g) RS-232C Input Connect the RS-232C output of your PC. h) RS-232C Output Connect the RS-232C input of another PDP. . The actual configuration on your PDP may be different, depending on your model. Remote Control Buttons ENG . Some remote control buttons do not operate with the PDP. AUTOMATIC SWITCH-OFF VCR/DVD FUNCTIONS; -STOP -REWIND -PLAY/PAUSE/ -FAST-FORWARD PIP FUNCTIONS; -PIP ON/OFF -INTERCHANGE THE MAIN AND THE SUB PICTURE (SWAP) -LOCATION SELECTION (LOCATE) -SIZE SELECTION (SIZE) -INPUT SOURCE SELECTION POWER ON/OFF (SOURCE) MAKE THE REMOTE CONTROL WORKS NUMERIC BUTTONS FOR MONITOR, VCR, CABLE, DVD PLAYER SELECT TO THE PC MODE DIRECTLY EXTERNAL INPUT SELECTION MENU DISPLAY/ PROGRAMME SELECTION BY NAME TEMPORARY SOUND SWITCH OFF TELETEXT NEXT PAGE CONTROL THE CURSOR IN THE MENU VOLUME INCREASE VOLUME DECREASE CHANGE CONFIRMATION TELETEXT PREVIOUS PAGE TELETEXT SUB-PAGE DISPLAYING INFORMATIONS/ PICTURE SIZE/ TELETEXT REVEAL TELETEXT SIZE SELECTION TELETEXT ON TELETEXT CANCEL VIDEO & TEXT MIX TELETEXT OFF (Refer to page 30 for details) STILL THE MAIN PICTURE FASTEXT TOPIC SELECTION SOUND EFFECT SELECTION PICTURE EFFECT SELECTION 8 . It is possible that the work of the transmitter is dull or not operated normally if the light of the Bulb is on around the PDP. Inserting the Batteries in the Remote Control ENG You must insert or replace the batteries in the remote control when you: . Purchase the PDP . Find that the remote control is no longer operating correctly Remove the cover on the rear of the remote control by pressing the symbol downwards and then pulling firmly to remove it. Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking care to respect the polarities: + on the battery against + on the remote control - on the battery against - on the remote control Replace the cover by aligning it with the base of the remote control and pressing it back into place. . Do not mix battery types, i.e. alkaline and manganese. Installing the Display on the Wall Attachment Panel . Wall attachment panel is sold separately. Check with your dealer. Installation Notes . Do not install the PDP on any place other than vertical walls. . To protect the performance of the PDP and prevent troubles, avoid the followings: -Do not install next to smoke and fire detectors. -Do not install in an area subjected to vibration or high voltage. -Do not install in the wall. -Do not install near or around any heating apparatus. . Use only recommended parts and components. continued... 9 10 ENG Installing the Display on the Wall Attachment Panel . Wall attachment panel is sold separately. Check with your dealer 1 Check for the stability of the wall where the PDP is to be installed. If the wall is not enough strong to support the PDP, strengthen the wall before installation. 2 Fix the wall attachment panel on the wall using bolts as shown in the figure: Fixing bolts must protrude from the wall appox. 1.5cm. 3 Using the wall attachment panel, you may adjust the angle of the display from 0 to 20 degrees. The angle can be set in 5 stages with 5 degrees of distance each using the angle control holes on the sides of the panel. When the angle has been set to 5 degrees. When the angle has been set to 15 degrees. When the panel hasn't been tilted. 5 degrees of tilt 10 degrees of tilt 15 degrees of tilt No tilt 20 degrees of tilt Angle control holes 11 Installing the Display on the Wall Attachment Panel ENG 4 Remove four large screws from the rear side of the display. Insert the bolts, dish-type washers, and insulation rubber into the four screw-holes as shown in the figure: 5 Put the insulation rubber point protruding from the rear top of the display in the groove on the top of the wall attachment panel. Lift up the display a little bit so that the insulation rubber point at the bottom of the rear side of the display is put to the groove at the bottom of the wall attachment panel. (Do not lift the display with any pressure. The insulation rubber at the top may be taken off.) Bolt Insulation rubber . OE Separating the Display from the Wall Attachment Panel ENG Remove the fixing bolts from both sides (left and right) of the wall attachment panel. Lift and pull the bottom of the display a small amount, to separate the insulation rubber point from the bottom of the wall attachment panel. Lift the display and separate the insulation rubber point from the groove on top of the wall attachment panel. . OE 12 Before Connecting the Display to External Equipment ENG Carefully check the connectors for position and type before making any connections. Loose connectors can result in picture or color problems. Make sure that all connectors are securely inserted into their terminals. Ferr...

Download now

Please, enter two numbers from picture: