Votes - 3, Average rating: 4
(
)
)
|
Other manuals for this model:
manual abstract
Network (Auto/Manual): Selects the Network ID setting mode among Auto or Manual. Network ID: When Network is Manual, you can set up Network ID using the numeric buttons. Frequency: Displays the frequency for the channel. (differs in each country) Modulation: Displays available modulation values. Symbol Rate: Displays available symbol rates. 14 English When Antenna Source is set to Satellite: ¦ ChannelType (All/TV/Radio): Select the Channel type to memorise. ¦ Satellite: Selects the satellite to scan. ¦ Scan Mode (All Channels/Free Channels Only): Selects the scanning mode of the selected satellite. Manual Store Scans for a channel manually and stores in the TV. . If a channel is locked using the ChildLock function, the PIN input window appears. When Antenna Source is set to Air or Cable: ¦ Digital Channel: When scanning has finished, channels are updated in the channel list. . When selecting Antenna> Air:Channel, Frequency,Bandwidth . When selecting Antenna> Cable:Frequency, Modulation,SymbolRate ¦ Analogue Channel (Programme, Colour System, Sound System, Channel, Search): If there is abnormal sound or no sound, reselect the sound standard required. . Channel mode • P (programme mode): When tuning is complete, the broadcasting stations in your area have been assigned to position numbers from P0 to P99. You can select a channel by entering the position number in this mode. • C (aerial channel mode) / S (cable channel mode): These two modes allow you to select a channel by entering the assigned number for each aerial broadcasting station or cable channel. When Antenna Source is set to Satellite: ¦ Satellite: Selects the satellite using the up/down buttons. ¦ Transponder: Selects the transponder using the up/ down buttons. ¦ Scan Mode (All Channels/Free Channels Only): Selects either free or all channels to store. ¦ Network Search (Disable/Enable): Enable / Disable network search using the up/down buttons. ¦ Signal Quality: Display the current status of broadcasting signal. . Information on a satellite and its transponder is subject to change depending on the broadcasting conditions. . When setting is completed, move to Search and press the ENTERE button. Channel scan is started. Satellite System Setup The PIN input screen appears. Enter your 4 digit PIN number. Satellite System Setup is available when Antenna is set to Satellite. Before running Auto Store, set Satellite System Setup. Then channel scan is run normally. ¦ Satellite Selection: You can choose the satellites for this TV. ¦ LNB Power (Off/On): Enables or disables the power supply for the LNB. ¦ LNB Settings: Configures the outdoor equipment. ¦ Satellite: Selects the satellite for receiving digital broadcasts. Transponder: Selects a transponder from the list or adds a new transponder. DiSEqC Mode: Selects DiSEqC mode for the selected LNB. Lower LNB Oscillators: Sets the LNB oscillators to a lower frequency. Upper LNB Oscillators: Sets the LNB oscillators to a higher frequency. Tone22kHz(Off/On/Auto): Selects the Tone 22 kHz depending on the LNB type. For a universal LNB it should be Auto. Signal Quality: Display the current status of broadcasting signal. ¦ Positioner Settings: Configures the antenna positioner. Positioner (On/Off): Enables or disables the positioned control. PositionerType (USALS/DiSEqC 1.2): Sets the positioned type between DiSEqC 1.2 and USALS(Universal Satellite Automatic Location System). – My Longitude: Sets the longitude for my location. – My Latitude: Sets the latitude for my location. – Satellite Longitude Settings: Sets the longitude of user defined satellites. User Mode: Sets the position of satellite antenna according to each satellite. If you store the current position of satellite antenna according to a certain satellite, when the signal of that satellite is needed, the satellite antenna can be moved to pre-populated position. – Satellite: Selects the satellite to set the position for. – Transponder: Selects a transponder from the list for signal reception. – Moving Mode: Selects the movement mode between discrete and continuous movement. – Step Size: Adjusts the step size degrees for the antenna rotation. Step Size is available when Moving Mode is set to Step. 03 Basic Features English 15 Basic Features – Go to Stored Position: Rotates the antenna to the stored satellite position. – Antenna Position: Adjusts and stores the antenna position for the selected satellite. – Store Current Position: Stores current position as the selected positioner limit. – Signal Quality: Display the current status of broadcasting signal. Installer Mode: Sets limits to the scope of movement of satellite antenna or reset the position. Generally, installation guide uses this function. – Limit Position (East/West): Selects the direction of the positioner Limit. – Antenna Position: Adjusts and stores the antenna position for the selected satellite. – Store Current Position: Stores the current position as the selected positioner Limit. – Go to Z...
Other models in this manual:Televisions - UE32C6005RW (20.25 mb)
Televisions - UE32C6200RS (20.25 mb)
Televisions - UE32C6500UW (20.25 mb)
Televisions - UE32C6510UP (20.25 mb)