Votes - 3, Average rating: 4.3
(
)
)
|
Other manuals for this model:
manual abstract
25 Using the Digital Favourite list ........................................................................................... 26 Using Optional Equipment Connecting Chart ........................................................................................................................... 27 Viewing Pictures from Connected Equipment............................................................................. 29 Using USB Photo Viewer ............................................................................................................... 30 Using BRAVIA Sync with Control for HDMI ................................................................................. 31 Using MENU Functions Navigating through Media Receiver Home Menu (XMB™)......................................................... 32 Settings ........................................................................................................................................... 33 Navigating through Monitor Home Menu..................................................................................... 41 Additional Information Specifications ................................................................................................................................. 47 Troubleshooting ............................................................................................................................. 50 : for digital channels only Before operating the TV, please read the “Safety information” section of this manual. Retain this manual for future reference. 3 GB Start-up Guide Start-up Guide 1: Checking the unit and accessories Monitor (1) Media receiver (1) Mains lead for monitor (1) Mains lead for mains adaptor (1) Mains adaptor for media receiver (1) Remote RMF-ED001 (1) Size AA batteries (R6 type) (2) IR Blaster (Y-cable) (2) Stand for media receiver (1) Terminal cover (1) Spacers (black) (4) 2: Installing the TV The following steps must be performed to correspond with the installation steps in the instruction manual of the optional accessories. Follow the instructions in this manual referring to the instruction manual supplied with the accessories. For explanations referred to in ( ) in the installation steps, see the same steps in the instruction manual supplied with the accessories. Installing on a TV stand Prepare the following item; – SS-TBL700 Speaker System (not supplied) ~ • Before performing the following instructions, first you must prepare the SS-TBL700 Speaker System (Table-Top Stand). Attach the Base Plate to the Table-Top Stand as shown in the instruction manual of the SS-TBL700 Speaker System. • Do not remove the blue tape that secures the plate on the rear of the monitor, until you finish installing the Table-Top Stand. 1 Remove the stand cover. Stand cover 2Gently slide the monitor onto the neck of the Table-Top Stand by aligning the Fmark of the plate to the top part of the Table-Top Stand. Be sure to work with two or more people. 4 GB • Do not put stress on the LCD panel or the frame around the screen. • Hold the Table-Top Stand firmly with both hands. 4 Connect the mains lead (supplied) to the AC IN socket. F mark Top part 3Attach the monitor to the Table-Top Stand using the screws (supplied with SSTBL700). Attach the two bottom screws first, then the top two screws. Start-~ • Insert the plug fully into the socket. • When using with an HDMI equipment, also connect the HDMI cable to the HDMI IN socket (page 27). Top screws Bottom screws ~ • If an electric screwdriver is used, set the torque to tighten at approximately 1.5 N·m {15 kgf·cm}. (Continued) 5 GB 6 GB 5 Attach the stand cover. Hang the stand cover over the top of the Table-Top Stand’s centre post, and then push down to close until it clicks. ~ • Be sure not to pinch the mains lead when attaching the cover. 6 Attach the terminal cover. 7 Connect the TV to your mains socket. Installing on a wall Prepare the following items; – SU-WL700 Wall-Mount Bracket (not supplied) – SS-WAL700 Speaker System (not supplied) – Spacers (black) (4) (supplied) 1 Place the supplied spacers (4-2). 1Remove the four screws from the rear of the monitor. 2Place the spacers (black) on the screw holes of the previous procedure. 2 Follow steps 4-3 to 4-4 referring to the instruction manual supplied with the Wall-Mount Bracket. When using only the Wall-Mount Bracket Proceed to the following step 5 in this manual. When using the Speaker System Proceed to the following step 3 in this manual. 3 Lift the Lock Bracket to insert the Speaker System (4-5). Screw Spacer Mounting Bracket Speaker System Lock Bracket Insert to the joint of the monitor This part goes on top of the Mounting Bracket 4 Fix the Speaker System with two screws (supplied with the Speaker System). 3: Connecting an aerial/Set Screws 5See the instruction manual supplied with the Wall-Mount Bracket, and follow steps 4-6 to 4-7. 6Connect the mains lead (supplied) to the AC IN socket (5-1). AC IN When installing the ...