Votes - 3, Average rating: 4
(
)
)
|
manual abstract
KV-HG21 © 2007 Sony Corporation M91 A Specifications KV-HG21M91 Note Power requirements 110-240 V AC, 50/60 Hz Indicated on the rear of the TV Power consumption (W) B/G, I, D/K, M Television system PAL, PAL 60, SECAM, NTSC3.58, NTSC4.43 Color system NICAM Stereo/Bilingual B/G, I, D/K; A2 Stereo/Bilingual B/G Stereo/Bilingual system English, Russian Teletext language Channel coverage B/G VHF : E2 to E12 /UHF : E21 to E69 / CATV : S01 to S03, S1 to S41 I UHF : B21 to B68 /CATV : S01 to S03, S1 to S41 VHF : C1 to C12, R1 to R12 / UHF : C13 to C57, R21 to R60 / CATV : S01 to S03, S1 to S41, Z1 to Z39 D/K VHF : A2 to A13 /UHF : A14 to A79 / CATV : A-8 to A-2, A to W+4, W+6 to W+84 M 8 (Antenna) 75-ohm external terminal Audio output (Speaker) 5 W + 5 W Number of terminal (Video)Input: 2 Output: 1 Phono jacks; 1 Vp-p, 75 ohms (Audio)Input: 3 Output: 1 Phono jacks; 500 mVrms (Component Input: 1 Phono jacks; Video) Y: 1 Vp-p, 75 ohms, sync negative CB: 0.7 Vp-p, 75 ohms CR: 0.7 Vp-p, 75 ohms i (Headphone) Output: 1 Stereo minijack FM Radio Tuning Range 87.5 - 108.0 MHz Intermediate 10.7 MHz Frequency Picture tube 21 in. Tube size (cm) 54 Measured diagonally Screen size (cm) 51 Measured diagonally Dimensions (w/h/d, mm) 638 . 458 . 482 Mass (kg) 25 Design and specifications are subject to change without notice. Made in Malaysia. Manufacturer: Sony Corporation Address: 1-7-1 Konan, Minota-ku, Tokyo 108-0075, Japan. B WARNING • Dangerously high voltages are present inside the TV. • TV operating voltage: 110 – 240 V AC. • Do not plug in the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground. •To avoid battery leakage and damage to the remote, remove the batteries from the remote if you are not going to use it for several days. If any liquid leaks from the batteries and touches your skin, immediately wash it away with water. For your own safety, do not touch any part of the TV, the power cord and the antenna cable during lightning storms. For children’s safety, do not leave children alone with the TV. Do not allow children to climb onto it. To prevent fire or shock hazard, do not expose the TV to rain or moisture. Do not place any objects on the TV. Do not operate the TV if any liquid Install the TV on a stable TV stand The apparatus shall not be or solid object falls into it. Have it and floor which can support the exposed to dripping or splashing checked immediately by qualified TV set weight. Ensure that the TV and that no objects filled with personnel only. stand surface is flat and its area is liquids, such as vases, shall be larger than the bottom area of the placed on the apparatus. TV. Do not block the ventilation Your TV is recommended for Do not plug in too many openings of the TV. Do not install home use only. Do not use the TV appliances to the same power the TV in a confined space, such in any vehicle or where it may be socket. Do not damage the power as a bookcase or built-in cabinet. subject to excessive dust, heat, moisture or vibrations. cord. Do not open the cabinet and the rear cover of the TV as high voltages and other hazards are present inside the TV. Refer servicing and disposal of the TV to qualified personnel. Clean the TV with a dry and soft cloth. Do not use benzine, thinner, or any other chemicals to clean the TV. Do not attach anything (e.g., adhesive tape, cellophane tape, glue) on the painted cabinet of the TV. Do not scratch the picture tube. Pull the power cord out by the plug. Do not pull the power cord itself. Even if your TV is turned off, it is still connected to the AC power source (mains) as long as the power cord is plugged in. Unplug the TV before moving it or if you are not going to use it for several days. C Getting Started Step 1 b Insert the batteries (supplied) into the remote. • Do not use old or different types of batteries together. Step 2 Connect the antenna cable (not supplied) to 8 (antenna input) at the rear of the TV. •Your TV can receive both TV and FM radio signals from the appropriate connections through the 8 (antenna input) terminal (see E). •You can also connect your TV to other optional components (see E). Step 3 Plug in the power cord, then press 1 on the TV to turn it on. • The 1 (standby) indicator flashes green for a few seconds when turning on the TV. This does not indicate a malfunction. Step 4 Set up the TV by following the instructions of the “Начальная настройкa” (“Initial Setup”) menu (see D). D Setting up your TV (“Initial Setup”) When you turn on your TV for the first time, the “Initial Setup” menu will appear. You can adjust settings below using the buttons on the remote control or TV front panel. Press V , v , B or b to select or adjust items, then press . 1 Select the desired menu language. EndSelect Confirm 2 Select “Yes” to preset the channels automatically. To skip automatic channel presetting, select “No”. Start Auto Program now? Ye...