Votes - 4, Average rating: 3.8
(
)
)
|
manual abstract
TV system: Colour system: PAL SECAM, NTSC 3.58, 4.43 (only Video In) Channel Coverage: I: UHF B21-B69 Picture Tube: Flat Display FD Trinitron WIDE: 32” (approx. 82 cm. measured diagonally) Rear Terminals 1/ 1 21-pin scart connector (CENELEC standard) including audio/video input, RGB input, TV audio/video output. 2/ 2 21-pin Scart connector (CENELEC standard) including audio / video input, RGB input, monitor audio/video output. 3/ S 3 21-pin Scart (SMARTLINK) connector (CENELEC standard) including audio / video input, S video input, selectable audio / video output and Smartlink interface. audio outputs (Left/ Right) - phono jacks Side Terminals S 4 S Video input – 4 pin DIN 4 video input – phono jack 4 audio input – phono jacks headphones jack Sound Output: 2 x 20 W (music power) 2 x 10 W (RMS) Woofer: 30 W (music power) 15 W (RMS) Power Consumption: 130 W Standby Power Consumption: 0.3 W Dimensions (w x h x d) : approx. 882 x 567 x 562 mm. Weight: approx. 63 Kg. Remote Control Locator coverage: up to 10 m. in open field The optimum distance is up to approximately 10 meters without interference. However, the distance may vary according to the surroundings and environment. Even within the signal reception area, there are some spots (dead spot) where the RF signal can not be received. This characteristics is inherent to RF signals, and does not indicate malfunction. Remote Control Locator Frequency: 434 MHz (ISM band). The frequency of your Remote Control Locator may be used by other devices (e.g. electric garage door). If the use of the Remote Control Locator causes interferences with any other device(s) please contact your nearest Sony Service Centre. Accessories supplied: 1 Remote Control (RM-937) 3 Batteries (IEC designated, AA size) Other features: • 100 Hz picture, Digital Plus. • Teletext, Fastext, TOPtext (250 page TEXT memory). • Sleep Timer. • Smartlink (direct link between your TV set and a compatible VCR. For more information on Smartlink, please refer to the Instruction Manual of your VCR). • Dolby Virtual. • BBE. • PIP. • Auto Format. • ACI (Auto Channel Installation). • Remote Control Locator. Design and specifications are subject to change without notice. Ecological Paper - Totally Chlorine Free Additional Information Troubleshooting Here are some simple solutions to problems which may affect the picture and sound. Problem Solution No picture (screen is dark) • Check the aerial connection. and no sound. • Plug the TV in and press the button on the front of the TV. • If the standby indicator is on, press TV button on the remote control. Poor or no picture (screen is • Using the menu system, select the “Picture Adjustment” dark), but good sound. menu and select “Reset” to return to the factory settings. No picture or no menu • Check that the optional equipment is on and press theinformation from equipment button repeatedly on the remote control until the connected to the Scart correct input symbol is displayed on the screen. connector. + button on the remote control. Good picture, no sound. • Press the • Check that “TV Speakers” is “On” in the “Sound Adjustment” menu. • Check that headphones are not connected. No colour on colour • Using the menu system, select the “Picture Adjustment” programmes. menu and select “Reset” to return to factory settings. When you switch on the TV • This is not a malfunction. Press the number buttons on the the last channel you were remote control to select the desired channel. watching before switching the TV off does not appear. GB Distorted picture when • Turn off any equipment connected to the Scart connector on changing programmes or the rear of the TV. selecting teletext. Distorted picture when • This is not a malfunction. It could be caused because some pressing the Remote Control broadcast TV uses the same frequency or a frequency close to Locator button. that of the remote control locator. This problem will disappear when you stop pressing the button. Wrong characters appear • Use the menu system to enter the “Language” menu (see page when viewing NexTView. 14) and select the same language that NexTView is broadcast in. continued... Additional Information 25 Problem Solution Picture slanted • Using the menu system, select the “Picture Rotation” option in the “Detail Set Up” menu to correct the picture slant. Noisy picture when viewing • Using the menu system, select the “Manual Programme a TV channel. Preset” menu and adjust Fine Tuning (AFT) to obtain better picture reception. • Using the menu system, select the “Noise Reduction” option in the “Picture Adjustment” menu and select “Auto” to reduce the noise in the picture. • The remote control beeps even if you have not pressed the remote control locator button, or: • When you press the remote control locator button, the remote control does not beep. • Using the menu system, assign an ID (number) to your remote control. (See “Remote Control ID” on page 17). • Replace the batteries of t...