Votes - 3, Average rating: 3
(
)
)
|
manual abstract
Your TV can receive either 525i/60Hz or 625i/50Hz interlace signals. • The component video terminals on your DVD player are sometimes labeled Y/CB/CR, Y/PB/ PR, Y/Cb/Cr or Y/B-Y/R-Y. • If you select “DVD” on your TV screen, the signal from the T (monitor output) jacks will not be output properly. This does not indicate a malfunction. Additional Information x Troubleshooting If you find any problem while viewing your TV, you can either use the “Factory Settings” function or check the Troubleshooting guide below. If the problem persists, contact your Sony dealer. “Factory Settings” function Press the WEGA GATE button. Choose “Settings” and go to “Setup” ( ) menu. From “Setup” menu, select “Factory Settings”. Then select “Yes” and press . Your TV will go blank for a few seconds, then the “Initial Setup” menu will appear. Your TV will be set to factory settings, but certain problems may be solved. Symptom Solutions Snowy picture, noisy sound • Check the antenna cable and connection on the TV, VCR and at the wall (see page 23). • Check the antenna setup. Contact a Sony dealer for advice. • Display the “Channel Setup” menu and select “Manual Program” to preset the channel again (see page 21). • Display the “Channel Setup” menu and set the “Signal Booster” to “Auto” from “Manual Program” (see page 21). • Try using an external booster. Distorted picture, noisy sound • Turn off or disconnect the external booster if it is in use. • Display the “Channel Setup” menu and set the “Signal Booster” to “Off” from “Manual Program”(see page 21). Good picture, noisy sound • Display the “Channel Setup” menu and select the appropriate “TV System” from “Manual Program” (see page 21). No picture, no sound • Check the power cord, antenna and VCR connections (see page 23). • Press ?/1 (power) to turn on the TV (see page 9). • Press ! (main power) on the TV to turn off the TV for about five seconds, then turn it on again (see page 8). Good picture, no sound • Press 2 + to increase the volume level (see page 9). • Press to cancel the muting (see page 9). Dotted lines or stripes • Do not use a hair dryer or other equipment near the TV. • Check the antenna setup. Contact a Sony dealer for advice. Double images or “ghosts” • Use a highly directional antenna. • Use the fine tuning (“Fine”) function (see page 21). • Check the antenna setup. Contact a Sony dealer for advice. • Turn off or disconnect the external booster if it is in use. No color • Display the “Picture” menu and select “Custom” from “Picture Mode”, then adjust the “Color” level from “Picture Adjustment” (see page 18). • Display the “Setup” menu and check the “Color System” setting (usually set this to “Auto”) (see page 22). • Check the antenna setup. Contact a Sony dealer for advice. continue Additional Information continued Symptom Solutions Picture slant • Keep external speakers or other electrical equipment away from the TV. • Display the “Picture Position” under “Setup” menu, then adjust “Picture Rotation” and “Picture V-Position” so that the picture is aligned to the TV screen (see page 22). Abnormal color • Keep external speakers or other equipment away from the TV. Do not patches move the TV while the TV is turned on. Press ! (main power) on the TV to turn off the TV for about 15 minutes, then turn it on again to demagnetize the TV. TV cannot receive stereo broadcast sound or Stereo broadcast sound switches on and off or is distorted. • Check the antenna cable and connection on the TV, VCR and at the wall (see page 23). • Check the antenna setup. Contact a Sony dealer for advice. Teletext display is • Check the antenna cable and connection on the TV, VCR and at the wall incomplete (see page 23). (snowy picture or double images). • Check the antenna setup. Contact a Sony dealer for advice. • Display the “Channel Setup” menu and set the “Signal Booster” to “Auto” from “Manual Program” (see page 21). • Try using an external booster. • Use the fine tuning (“Fine”) function (see page 21). TV cannot receive FM radio station. • Connect a separate FM antenna and the TV channel source through an antenna selector (switch) to your TV (see page 23). The 1 (standby) indicator on your TV flashes red several times after every three seconds. • Count the number of times the 1 (standby) indicator flashes. Press ! (main power) to turn off your TV. Contact your nearest Sony service center. The TV screen sometimes goes blank for slightly longer than usual during channel change. • The “Signal Booster” is functioning to detect a weak signal. This does not indicate a malfunction. TV cabinet creaks. • Changes in room temperature sometimes make the TV cabinet expand or contract, causing a noise. This does not indicate a malfunction. A small “boom” • The TV’s demagnetizing function is working. This does not indicate a sound is heard malfunction. when the TV is turned on. Additional Information x Specifications KV-SZ29M91 KV-SZ25M91 Note Power requirements 220-240 V AC, 50/60 Hz Power consumptio...