Votes - 5, Average rating: 4.4
(
)
)
|
Other manuals for this model:
manual abstract
• Do not place the remote control in a location near a heat source, or in a place subject to direct sunlight, or in a damp room. 4 GB 2: Attaching the stand Packaging material Stand Packaging material 3 Start- up Guide 90° 4 1 Take out the stand, screws, and packaging material to begin stand setup. 2 Set the packaging material as shown. 3 Place the TV directly to the stand as shown. After placing the TV on the stand, remove the packaging material. 4 Fix the TV to the stand using the supplied screws. Notes • This TV is very heavy, so two or more people should place the TV on the stand. • If using an electric screwdriver, set the tightening torque at approximately 1.5 N·m (15 kgf·cm). 5 GB 3: Connecting an aerial/ 4: Preventing the TV VCR from toppling over Connecting an aerial only Connecting an aerial and VCR Coaxial cable (supplied) Mains lead (supplied) Scart lead (not supplied) Coaxial cable (supplied) VCR Mains lead (supplied) Coaxial cable (not supplied) 2 3 1 5: Bundling the cables 6 GB 3 Press F/f/G/g to select the language displayed on the menu screens, then press 6: Selecting the . language and country/ region 2 3,4 3,4 1 Connect the TV to your mains socket (220240V AC, 50Hz). 2 Press 1 on the TV (top side). When you switch on the TV for the first time, the Language menu appears on the screen. When the TV is in standby mode (the 1 (standby) indicator on the TV (front) is red), press "/1 on the remote to switch on the TV. 4 Press F/f to select the country/region in which you will operate the TV, then press . 12 If the country/region in which you want to use the TV does not appear in the list, select “-” instead of a country/region. The message confirming the TV start auto-tuning appears on the screen, then go to “7: Auto-tuning the TV”. Start- up Guide 7 GB 7: Auto-tuning the TV The TV will now search for and store all available TV channels. 2 4 1 Before you start auto-tuning the TV, insert a pre-recorded tape into the VCR connected to the TV (page 6) and start play back. The video channel will be located and stored on the TV during auto-tuning. If no VCR is connected to the TV, this procedure is not required. Go to step 2. 2 Press G/g to select “OK”, then press . The TV starts searching for all available digital channels, followed by all available analogue channels. This may take some time, please be patient and do not press any buttons on the TV or remote. If a message appears for you to confirm the aerial connections No digital or analogue channels were found. Check all the aerial connections and press to start auto-tuning again. 3 When the Programme Sorting menu appears on the screen, follow the steps of “Programme Sorting” (page 32). If you do not change the order in which the analogue channels are stored on the TV, go to step 4. 4 Press MENU to exit. The TV has now tuned in all the available channels. Note When a digital broadcast channel cannot be received, or when selecting a region in which there are no digital broadcasts in step 4 under “6: Selecting the language and country/region”, the time must be set from “Clock Set” in the “Set-up” menu (page 29) after performing step 4. 8 GB Safety information Mains lead • Observe the followings to prevent the mains lead being damaged. If the mains lead is damaged, it may result in a fire or an electric shock. – Unplug the mains lead when moving the TV set. – When you disconnect the mains lead, disconnect it from the mains socket first. – Be sure to grasp the plug when disconnecting the mains lead. Do not pull on the mains lead itself. – Do not pinch, bend, or twist the mains lead excessively. The core conductors may be exposed or broken. – Do not modify the mains lead. – Do not put anything heavy on the mains lead. – Keep the mains lead away from heat sources. • If you damage the mains lead, stop using it and ask your dealer or Sony service centre to exchange it. • Do not use the supplied mains lead on any other equipment. • Use only an original Sony mains lead, not other brands. Mains socket • The TV set with a three-wire grounding type mains plug must be connected to a mains socket with a protective earthing connection. • Do not use a poor fitting mains socket. Insert the plug fully into the mains socket. A poor fit may cause arcing and result in a fire. Contact your electrician to have the mains socket changed. Cleaning the mains plug Unplug the mains plug and clean it regularly. If the plug is covered with dust and it picks up moisture, its insulation may deteriorate and result in a fire. Overloading This TV set is designed to operate on a 220–240 V AC supply only. Take care not to connect too many appliances to the same mains socket as this could result in a fire or an electric shock. When not in use • If you will not be using the TV set for several days, the TV set should be disconnected from the mains for environmental and safety reasons. • The TV set is not disconnected from the mains when the TV set is switched off. To disconnect the TV set...
Other models in this manual:Televisions - KDL-46W2000 (5.62 mb)