Votes - 5, Average rating: 4.2 ( )

Manafacture: Panasonic File size: 1.4 mb File name: Language of manual:

• The computer shown in the illustration is for example purposes only. • Additional equipment and cables shown are not supplied with this set. • Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range. • Component Input is possible with the pin 1, 2, 3 of the D-sub 15P Connector. Signal Names for D-sub 15P Connector 1 678 3 9 45 10 1514131211 2 Pin Layout for PC Input Terminal Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name 1 R (PR/CR) 6 GND (Ground) 11 GND (Ground) 2 G (Y) 7 GND (Ground) 12 SDA 3 B (PB/CB) 8 GND (Ground) 13 HD/SYNC 4 GND (Ground) 9 NC (not connected) 14 VD 5 GND (Ground) 10 GND (Ground) 15 SCL Connections SERIAL Terminals connection The SERIAL terminal is used when the Plasma Display is controlled by a computer. 9876 5321 4 SERIAL Pin layout for RS-232C COMPUTER RS-232C Straight cable D-sub 9p Notes: • Use the RS-232C cable to connect the computer to the Plasma Display. • The computer shown is for example purposes only. • Additional equipment and cables shown are not supplied with this set. The SERIAL terminal conforms to the RS-232C interface specification, so that the Plasma Display can be controlled by a computer which is connected to this terminal. The computer will require software which allows the sending and receiving of control data which satisfies the conditions given below. Use a computer application such as programming language software. Refer to the documentation for the computer application for details. Communication parameters Signal level RS-232C compliant Synchronization method Asynchronous Baud rate 9600 bps Parity None Character length 8 bits Stop bit 1 bit Flow control - RS-232C Conversion cable D-sub 9-pin female Details 2 R X D 3 T X D 5 GND 4 6• Non use 7 8 Shorted91 • NC Basic format for control data Command The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order. If there are no parameters, then the parameter signal does not need to be sent. STX ETX C1 C2 C3 P1 P2 P3 P4: P5 Colon Parameter(s) End Start 3-character (1 - 5 bytes) (03h) (02h) command (3 bytes) Notes: • If multiple commands are transmitted, be sure to wait for the response for the first command to come from this unit before sending the next command. • If an incorrect command is sent by mistake, this unit will send an “ER401” command back to the computer. Command Parameter Control details PON None Power ON POF None Power OFF AVL ** Volume 00 - 63 AMT 0 Audio MUTE OFF 1 Audio MUTE ON IMS None SL1 SL2 SL3 PC1 Input select (toggle) Slot1 input Slot2 input Slot3 input PC input DAM None NORM ZOOM FULL JUST SELF Screen mode select (toggle) NORMAL (4 : 3) ZOOM FULL JUST Panasonic AUTO With the power off, this display responds to PON command only. Connections AV & COMPONENT connection COMPONENT VIDEO OUT RR SLOT2 SLOT3 VIDEO IN VIDEO OUT PR/CR/R PB/CB/B Y/GAUDIOR L COMPONENT/RGB IN AUDIO IN R L S VIDEO IN PC VIDEO VIDEO IN S VIDEOR L PB Y L R MONITOR RCA-BNC adapter plug Example of input signal source DVD Digital TV-SET-TOP-BOX (DTV-STB) Y, PB, PR, OUT AUDIO OUT SLOT1 Example of input signal source OUT OUT OUT AUDIO Notes: • Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “COMPONENT”. (see page 36) • Additional equipment, cables and adapter plugs shown are not supplied with this set. S VIDEO VCR CAMCORDER VCR RGB signal (R, G, B, HD, VD) VIDEO IN VIDEO OUT PR/CR/R PB/CB/B Y/GAUDIOR L COMPONENT/RGB IN Computer RGB Camcorder or Notes: • Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “RGB”. (see page 36) • Additional equipment, cables and adapter plugs shown are not supplied with this set. Power ON / OFF Connecting the AC cord plug to the Plasma Display. Fix the AC cord plug securely to the Plasma Display with the clamper. (see page 9) Connecting the plug to the Wall Outlet Press the Power switch on the Plasma Display to turn the set on: Power-On. Power Indicator: Green INPUT MENU ENTER/+/VOL-/ TH-42PWD8 TH-42PWD8 Power Indicator Example: The screen below is displayed for a while after the Plasma Display is turned on. (setting condition is an example.) Remote Control Sensor When the POWER is turned on for the first time, the LANGUAGE selection screen is displayed. From the second time on, language selection can be done from the setup menu. (see page 18) Select the desired language using the or button and press the ACTION ( ) button. From the second time on, the screen shown below is displayed for a while (setting condition is an example). English (UK) Deutsch Francais Italiano Espanol ENGLISH (US) Русский OSD Language SetSelect Press the button on the remote control to turn the Plasma Display off. Power Indicator: Red (standby) Press the button on the remote control to turn the Plasma Display on. Power Indicator: Green Turn the power to the Plasma Display off by pressing the switch on the ...

Download now

Please, enter two numbers from picture: