Votes - 5, Average rating: 4.2
(
)
)
|
manual abstract
Press again to restore sound. Channel Change - (Two options) Option 1. Press the CHANNEL (CH) UP or DOWN button to sequentially scan through programmed channels (when On Screen menus are not displayed). NOTE: Press the TV Mode button to operate TV Remote functions, if necessary. Located On Remote Control Selects Next Higher Channel Selects Next Lower Channel Keyboard “0 through 9” Buttons Option 2. Press two digits on keyboard (Example press 0, then 5 for channel 05). For channels over 99, press three digits on keyboard. © ®~! VCR Function Buttons - The VCR FUNCTION buttons have been designed to operate numerous brands of VCRs. The infrared code must be obtained prior to use. (Please refer to Programming the Universal Remote for programming instructions.) NOTE: Press the VCR Mode Selection button to operate VCR Remote functions. Helpful Hints: • Helpful information will display On Screen momentarily when Receiver is first turned on and when the channel is changed. • When using keyboard entry for channels 10,11 and 12 in the CABLE mode there is a slight delay before channel change because of the capability of tuning cable channels 100 to 125. NOTE: If “SPEAKER OFF’ is displayed On Screen after pressing the VOLUME button, refer to Audio Menu to turn Speakers “ON”. -14- Helpful Hints: ■ Press Ihe TV Mode Selection button to operate TV Remote functions, if necessary TV/Video Button — Press the TV/VIDEO button [□ select desired input for Main Picture or PIP frame (when the PIP is displayed) Signal connected to REAR VIDEO/AUDIO INPUT 2 JACKS REAR VIDEO/AUDID _ INPUT 1 JACKS TV Dr CABLE Signal connected to REAR VIDEO/AUDID INPUT 2 JACKS ■ REAR VIDEO/AUDIO _B INPUT 1 JACKS TV Dr CABLE PIP VIDEO Z PIP VIDEO 1 PIP CH D2 PIP Frame Recall Button - Press the RECALL button to review ■ Audio Mode status - CH number Dr Video Inpul selected ■ Sleep Timer status - Clock time ■ Channel Caption (Station Identifier) R-Tune (Rapid Tune) Button “ Press the R-TUNE (RAPID TUNE) button to instantly switch between the last two channels selected (without any On Screen display being activated) CHANNEL NOW BEING VIEWED Multi Button The MULTI button can be programmed lo operate up lo 6 Remote funclion buttons at the same time For Example: TV Power/On, VCR Power/On and Cable box Power/On (selected brands) can be operated at the same time with one press of the MULTI button Procedure 1 First program the Remote for the selected device Infrared access code Confirm lhat the Remote Control is compatible with the equipment 2 Face the Remote Control transmitter away from all equipment remote sensors 3 Press and hold the Remote POWER button, then press and hold the ACTION button down at the same time for three seconds (All previous commands are erased ) PRESS AT THE SAME TIME FOR THREE SECONDS 4 After three seconds, let go of the POWER and ACTION buttons 5 Press the MULTI button (Waiting more than 30 seconds without pressing another button will exitthe programming mode) 6 Press a maximum of 6 Function buttons on the Remote Each button you press is equal to one function If six Remote button functions ate entered, all will register in the MULTI button memory in the sequence entered When finished, press the MULTI button to end the program mode The Following is an example flow chart of Remote functions that can be programmed into the MULTI button (The VCR Mode button should be programmed before starting procedure see pg. 37) PROGRAM MODE Now you can turn the TV and VCR ON/OFF at the same time with one press of the MULTI button To delete entered functions - Press and hold the Remote POWER button then press and hold Ihe ACTION button down at the same time Tor three seconds Now you can enter from one to six different Remote functions NOTE. You can also program the MULTI button to perform most individual Remote Control button functions Buttons which continuously perform a function as long as pressed (Volume Up/Down, Channel Up/Down, etc ) cannot be programmed Only those buttons which perform a function when initially pressed (Power On/Off, Mute, Direct Channel Entry, etc ) can be programmed -15- Press the TV Mode Selection button to operate TV Remote functions, if necessary ^ Swap Button — Press the SWAP button (when the PIP frame is displayed) to interchange what is being viewed on the Mam Picture with that of the PIP frame PIP (Picture in Picture) Button - This feature allows the viewer to monitor one channel program while watching another The monitored source (PIP) can be a different channel or a different video source (such as a VCR) when connected to the input jacks ■ S-VideD connection will also operate the PIP feature (refer to OPTIONAL S-VIDEO VHS CONNECTION section) ■ When the Main Picture is in Video mode with no signal, the PIP will not operate properly CH 02 PIP VIDEO VIDEO PIP CH 02 Audio will be that of the Main Picture PIP Operation 1 Press the TV...