Votes - 4, Average rating: 3.5
(
)
)
|
Other manuals for this model:
manual abstract
• This product has been designed for application on a vertical wall in commercial and residential buildings, constructed of wood wall studs or masonary (solid concrete, brick, and stone). If you are unsure of your wall composition or for assistance with other surfaces, contact a qualified installer. • This product is not designed for use on walls constructed of metal studs. If you are unsure of your wall composition or for assistance with other surfaces, contact a qualified installer. • The wall or mounting surface must be capable of supporting the combined weight of the mount and the display; otherwise the structure must be reinforced. • Do not exceed the maximum load capacity of 132lbs for this product. • Fits 30-55” screens • Safety gear and proper tools must be used. Failure to do so can result in property damage and/or serious injury. • A minimum of two people are required for this installation. Do not attempt to install this mount alone under any circumstance. • Follow all instructions and recommendations regarding adequate ventilation and suitable locations for mounting your display. Consult the owner’s manual for your display for more information. • This mount is equipped with a safety device that must be used whenever the mount holds a display. Not using the safety device can cause property damage, serious injury, or death. 2 Your fixed wall mount Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at Designed to fit most TV brands with a focus on safety and ease of use. Includes Easy 1-2-3 installation kit, complete with: all necessary hardware for mounting on different types of walls, mounting templates and bubble level. C-UL US listed for weight capacity up to 132lbs. 2.1 What’s in the box. Wall mount Cotter pin Bag #1 (A) M4x12 Bolt (x4) (B) M4x30 Bolt (x4) (C) M4 Lock Washer (x4) Bag #2 (D) M5x12 Bolt (x4) (E) M5x30 Bolt (x4) (F) M5 Lock Washer (x4) Bag #3 (G) M6x12 Bolt (x4) (H) M6x35 Bolt (x4) (I) M6 Lock Washer (x4) Bag #4 (J) M8x16 Bolt (x4) (K) M8x40 Bolt (x4) (I) M8 Lock Washer (x4) Bag #5 (M) Small Spacer (x4) (N) Large Spacer (x4) (O) M6 Washer (x4) Bag #6 (P) Concrete Anchor (x6) (Q) M8x63 Lag Bolt (x6) (R) Lag Bolt Washer (x6) 2.2 What you’ll also need. • Phillips head screwdriver • Ratchet or driver with 1/2” (13 mm) socket • Portable or electric drill • 1/4” (6 mm) drill bit and stud finder for drywall installation • 3/8” (10 mm) masonry bit for concrete installation • Stud finder Installing your wall mount In this chapter, the basic steps to get you started are described. B Warning Carefully read the safety precautions in “Section 1 Important” before you install the wall mount. 3.1 Mounting the wall plate (drywall) B Warning For safety reasons, this mount must be secured to two adjacent wood studs at least 16” apart.The studs must be capable of supporting the combined weight of the mount and display. 1 See enclosed mounting template for diagram and guide of how to mount properly on the wall. 2 Using a stud finder, locate and mark two adjacent studs for securing the mount (make sure your marks are in the center of each stud). D Note Once studs have been located you will need to verify with a hammer and a nail A) Simply place the nail over your mark on the wall and tap in with hammer. if the nail encounters resistance and is secure in wall you have verified a stud location B) If it just pushes through with no resistance you will need to start over and locate the stud. 3 Using the enclosed mounting template, place the diagram against the wall and mark four locations (two per stud) on the wall where the mount Is to be Installed. Be sure to use the center of each stud. 4 With the help of another person, place the mount against the wall and level it using the bubble guide. 5 While another person holds the mount in place, mark four locations (two per stud) on the wall where the mount is to be installed. Be sure to use the center of each stud. (these marks should line up with the ones made in step 3 above using the template). 6 Set the mount aside and drill a 1/4” (6 mm) pilot hole at each marked location. 7 Place the mount back against the wall and secure it using the lag bolts (Q) and lag bolt washers (R) provided. Do not over-tighten these bolts and do not release the mount until all bolts are in place. 8 Once all (4) lag bolts are in place you must tighten each one. (note: be sure not to over tighten). 1 1 3.2 Mounting the wall plate (concrete) B Warning For safety reasons, the concrete wall must be capable of supporting the combined weight of the mount and display. 1 See enclosed mounting template for diagram and use enclosed mounting template as a guide for precision mounting. 2 Using the enclosed mounting template, place the diagram against the wall and mark six locations on the wall where the mount Is to be Installed. 3 With the help of another person, place the mount against...
Other models in this manual:Televisions - SQM5822 (912.38 kb)