Votes - 6, Average rating: 3.8
(
)
)
|
manual abstract
• If you have an S-VHS VCR, use the S INPUT cable in place of the standard video cable. REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT TRANSMITTER BATTERY INSTALLATION AND REPLACEMENT Open the battery cover of the Remote transmitter by pushing the notched part of the cover with your finger. a) Push the batteries towards the spring and lift them out. b) Replace old batteries with two new "AA" size (SUM-3) batteries or equivalent. c) Match the (+) and (-) marks in the battery compartment. d) Replace the cover. CAUTIONS 1. If your television set is to remain unused for a long period of time, for instance, when you go on a vacation, unplug the television set from the wall outlet. 2. Do not subject the Remote transmitter to shocks such as dropping it on the floor, etc. Precision parts may be damaged. 3. Do not allow the Remote transmitter to become wet and avoid placing it in areas of high humidity. Don't leave it on or near a heater. Excess heat or moisture may cause the unit to cease operation. 4. If the batteries become exhausted, Remote control operation may become erratic or stop altogether. Replace the old batteries with two fresh "AA" (SUM-3) types. NOTES 1. When the power button is set to OFF, the OFF TIMER is released. 2. The channel No. indication, volume indication and OFF TIMER indication are not displayed simultaneously. 3. To operate your TV, point the Remote transmitter at the remote sensor of the TV. ACCESSORIES PART NUMBERS ACCESSORIES PART NUMBERS For information regarding how to obtain these accessories, please call TOLL FREE 1800- 448-2244 fro your nearest Hitachi Authorized Parts Distributor in the continental United States. For Alaska and Hawaii, please contact the nearest Hitachi Regional Office. Accessories chart CAUTION: The television stands Model SP313G and Model SP350G are designed for use only with Hitachi TV Models 31GX31B, 31DX11/21B. Use with other television equipment may result in instability, causing possible injury. NOTES 1. To operate your TV, be sure to point the Genius Remote at the remote sensor on the television. To operate other electronic equipment like a VCR, point the remote at the remote sensor on the device. 2. Refer to the instruction manual of the VCR for operation of the buttons exclusively for the VCR. 3. Be sure to keep the original remote transmitter even after storing its codes in the Genius Remote Control If the Genius Remote is left with its batteries removed, the learned codes in its memory are erased and will have to be reprogrammed into the memory. 4. The Genius Remote Control may not be abel to learn certain special remote codes. Caution on batteries • The Genius Remote Control is working when the LEARN indicator lights up when a button is pressed. • When you press a button and the LEARN indicator will not light up or if the operation is extremely slow, this is an indication that the batteries should be replaced. • Even if the batteries seem dead, do not remove them until you have replacement batteries ready to put in. The codes stored in memory will be erased in a few minutes without power. When replaceing batteries prepare the new ones first. TROUBLESHOOTING TROUBLESHOOTING RECEPTION PROBLEMS (EXTERNAL TO THE TV) • IGNITION NOISE: Black spots or horizontal streaks may appear, picture may flutter or drift. Usually caused by interference from automobile ignition systems, neon lamps, electrical drills and other electrical appliances. • GHOSTS: Ghosts are caused by the television signal following two paths. One is the direct path and the other is reflected from tall buildings, hills or some other objects. Changing the direction or position of the antenna may improve reception. Ghosting may also be caused by defects in the antenna system such as unshielded leads or connecting several sets to the same antenna without using multiple antenna couplers. • SNOW: If your receiver is located in the fringe area of a television station where the signal is weak, your picture may be marred by the appearance of small dots. When the signal is extremely weak, it may be necessary to install a special antenna to improve the picture. • RADIO FREQUENCY INTERFERENCE: The interference produces moving ripples or diagonal streaks, and in some cases, causes loss of contrast in the picture. CHECK HERE BEFORE CALLING FOR SERVICE Troubleshooting chart SPECIFICATIONS SPECIFICATIONS Features: • Super Fine Quality 650 Lines Horizontal Resolution • Dark Tint CPT for 31GX31B • Genius Remote (Controls many VCR brands and cable box brands) • Full Function Menu On-Screen Display • Full Set of Input Jacks, including S-Video • Closed Caption Decoder Inputs: • Power input....................................AC 120V, 60Hz • Power Consumption (operating) 31GX31B.......................135W Other models...................116W • Power Consumption (maximum) 31GX31B.......................180W Other models...................155W • Antennal input impedance...............75 . • Channel coverage........