Votes - 3, Average rating: 4 ( )

Manafacture: Hitachi File size: 6.76 mb File name: 16dc96d3-e345-ca64-5d0d-50e884637d02.pdf Language of manual:

Press ADJUST , , or to select the check box for each function to be learned. 2. Press ENTER and the function name will begin to flash to confirm the ready-to-learn status. 3. Press the button on the device’s remote control that corresponds to the selected function. A check mark will appear and the function name will stop flashing. This confirms the signal learned status. 4. To test the learned command, press the ENTER button on the TV remote while the learned function is still highlighted. The device should perform the selected function. The device needs to be turned on and the IR emitters properly placed for the test to be successful (see page 31 for IR emitter placement). 5. Repeat for each function to be learned. 6. To erase a learned function, highlight the check box for that function and press CANCEL. 7. When the function signals have been learned, press ADJUST to select Next> and move to the [Device] Advanced Learn screen. NOTE: When learning the device’s remote control signals, point the device’s remote control at the TV screen. Hint: If the device’s remote control uses a single button for both Power On and Power Off, don’t learn the Power Off function. Figure 16. [Device] screen Edit NetCommand®, Add Devices, continued Figure 17. [Device] Learn screen Figure 19. Name screen [Device] Advanced Learn Screen Figure 18 After learning the basic device keys, the [Device] Advanced Learn screen allows you to learn any special keys for your device. Most common IR remote control signal formats can be learned by NetCommand. A table of specialized device keys is shown in Appendix E. You only need to learn the functions your devices respond to and can ignore the functions that do not apply to your device. Connection for [Device] Screen Figure 20 This screen allows the TV to learn the connection between device(s) and input(s). Inputs 1-3, Components 1–3, HDMI 1 and 2, and/or the inputs for the A/V Receiver all need to be checked, if connected. Add or remove check marks to indicate what type of connections (Audio or Video) are used with each TV and A/V Receiver input. Figure 18. [Device] Advanced Learn screen Name Screen Figure 19 The Name screen allows you to change the default name for each device to a custom name of up to eight characters (including a blank space), selecting from letters, numbers and nine different characters. Press ADJUST or to select each letter, then press ENTER to move to the next position. Press CANCEL on the remote to delete the current letter and move back one character position. When in the first position, the CANCEL button will return the name to the default name. Figure 20. Connection for [Device] screen Edit NetCommand®, Add Devices, continued The screens described below may not be necessary for your device setup. If they do not display automatically on screen, they are not required. IR Code for [Device] Screen Figure 23 This screen only displays if an added device has the same IR code as a previously added device of the same type and manufacturer. You can specify the IR setting for the new device. For example, for the second Mitsubishi VCR you can specify the IR Code setting to VCR-B, if the primary Mitsubishi VCR is using the VCR-A IR code. VCR for Recordings Screen Figure 21 Select the VCR to use for making analog recordings through NetCommand or the TV Guide On Screen® system. The VCR inputs must be connected to RECORD OUT on the TV, which outputs analog downconverted from digital. Figure 21. VCR for Recordings screen Figure 23. IR Code for [Device] screen RF Connection for Cable Screen Figure 22 The RF Connection for Cable screen displays only when adding or changing a Cable Box. If your Cable Box is connected to a TV Antenna input, check the RF check box. Select the TV antenna input that is used with the Cable Box. Select the channel number used for output by your cable box. The default channel is 003. If the Cable Box is also connected to a VCR for recording, select that VCR. If your Cable box is connected using Audio/Video or component cables, make sure the RF check box is unchecked. Then the next screen will be Connection (Figure 20), to allow the selection of the TV input used with the Cable Box. Figure 22. RF Connection for Cable screen Edit NetCommand®, Change or Delete Devices, Finish Screen Finish Screen Figure 26 To finalize your selections and complete the NetCommand setup, select Finish from the Finish screen. Note: To change any of the inputs or names for the devices, or add devices not included in the initial settings, select Edit to display the Edit NetCommand menu. Change Device Screen Figure 24 Selecting Change from the Setup menu screen, displays the Change screen. To change a device, select the device by name, not type. You can change the name or input connections to the TV and A/V receiver. If “Other” was selected for the manufacturer then you can also “Learn”. The rest of the screens that follow are the same as when you Add a device. Figure 24. Change screen ...

Download now

Please, enter two numbers from picture: