|
manual abstract
6 Please, make sure to connect the power plug to the wall outlet socket after connecting the TV to the power cord! 1. Install the base stand; place the TV on a solid surface. Ensure that the TV is placed in a position to allow free flow of air. Do not cover the ventilation openings on the back cover. To prevent any unsafe situations, no naked flame sources, such as lighted candles, should be placed on or in the vicinity. Avoid heat, direct sunlight and exposure to rain or water. The equipment shall no t be exposed to dripping or splashing. 2. Connect the antenna cable or CATV cable to the aerial socket ANT IN 75. at the back of the TV set. PREPARATION Min 1 m 7 English 3. Remote control: Remove the cover of the battery compartment. Insert the 2 batteries supplied (Type AA 1.5V). English 4. Power: Insert the power cord in the wall socket having an AC power supply.You can see LED states at the front panel. If the LED color is Green , means the TV set is power on. If the LED color is amber, which means this TV set is in stand by state. 5. Turn on the TV: Push the POWER key on the Remote control or the control knobs on right of TV. The TV will be power-on and the user can see the display on the screen after a few seconds . POWER key 8 PERIPHERAL CONNECTION GUIDE AC POWER Note: The MUTE key on the remote control works on both TV internal speaker and the earphone output. Once your equipment is connected, use the following procedure to view the input signal: Press the source button on the remote controller to select the relevant source to view. (ex: Press VIDEO button to select “Video1 Composite Rear” if you have c onnected a DVD player to Video1 Composite socket.) "HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC." 9 English TO USE THE PANEL CONTROL OPERATION INSTRUCTIONS 1 VOL VOL : Press to increase the sound volume level. 2 VOL 3 CH CH : Press to select the next higher Program number. 4 CH CH : Press to select the next lower Program number. 5 MENU Menu key: Press to open or exit the OSD menu. key: Press to select the input source. 7 POWER Power key: Press to turn on / off (standby) the TV set. (Please re-turn on TV after the Power-ON status LED had changed to the orange color and finished flashing.) 6 INPUT Input 10 VOL : Press to decrease the sound volume level. English TO USE THE REMOTE CONTROL TO USE THE REMOTE CONTROL “0 ~ 9 /- number” Press to enter TV channel number to select channel (Press ‘-’ to indicate choosing the sub-channel). “MENU” Press to open or exit menu. “VOL- / VOL+” Press + or - to adjust the volume. “CH-/ CH +” Press + or - to browse through the TV channels. “ ”,“ ”,“<”,“>”,“OK” Press to adjust the various function items on the menu. “INFO” Press to show the information about the input source.TV channel.display resolution and current time. “VIDEO” Press repeatedly to choose S-Video/ Composite source mode (Video 1 ~ 2). “SLEEP” Press to set a time period (off/5min/15min 30min/45min/60min/90min/120min/180min/ 240min) after which the TV should switch itself to standby mode. “COMP” Choose Component source mode (Video 3). “FREEZE” Press to freeze the displayed picture “POWER” Press to power ON/OFF (standby) TV. (Note:1.TV is never completely power off unless physically unplugged. 2.Press to turn on TV after the power on status LED had changed to the amber color and stopped flashing. ) “MUTE” Press to set TVsound mute ON/OFF. “MTS/SAP” Press to activate the NTSC TV sounds, such as: Stereo, SAP or Mono tone. “PRE CH” Press to display the previous TV . “WIDE” Press to choose the display aspect as: Normal, Wide, Zoom or Cinema mode. “Exit” Press to exit menu or OSD. “FAV” Press to display the favorite TV channel. (After setting the favorite TV channel on main menu.) “PC” Press repeatedly to choose VGA or HDMI source mode (Video 4 ~ 5). “V-CHIP” Press to lock / unlock Parental Control temporarily. (After setting the restricted table of MPAA or TV Rating.) “TV” Press to choose ATSC/NTSC TV source mode. “CC” Press repeatedly to turn on/off CC or CCon when mute. English 11 EnglishEnglish TO USE THE MENUS 1. Press the MENU button to display the main menu 2. Use the cursor up/down to select a menu item. 3. Use the cursor left/right to enter a submenu. 4. Press the OK button to enable/disable the function. 5. Press the MENU or EXIT button to exit the menu. Press the MENU button to enter the main OSD (On Screen Display). Adjust the items including Setup menu, Video menu, Audio menu and Feature menu. However, some function items in the menus may only be enabled in the particular source modes. SETUP MENU The Setup menu in TV mode shows as below. In others source modes, the Setup menu only shows Menu Language and Aspect Ratio items. 1. Tuning Band: Select TV source signal from the Air (antenna) or Cable (CATV). 2. DTV Signal: Show the intensity of the received DTV signal. 3. Auto Ch Search: Automatically scan all NTSC / ATSC TV channel...
Other models in this manual:Televisions - L19W761 (6.07 mb)