Votes - 5, Average rating: 3.4
(
)
)
|
manual abstract
· Enter the service mode and select service adjustment S5. · You can see the OSD as shown in below. IF CONTROL AUTO RFAGC START VIDEOL 7 RFAGCD 10 FM.LEV 8 AGC POINT 3.75 A/D VALUE : 8DH .a.aMOVE....ADJUST RECALL : SET · Select RFAGCD item, press the volume up or down button until noise or beat in picture disappears. · Press the DISPLAY button to memorize the data. 4) GEOMETRIC ADJUSTMENTS (S6) · Enter the service mode and select service adjustment S7. · Whenever you select the “S7” using the volume up or down button, the screen is changing like this. NORMAL BLACK WHITE100 WHITE60 CROSS · Using the volume up or down button, select internal cross pattern. · Select service adjustment S6 · You can see the OSD as shown in below. GEOMETRY H. PHASE 20 V. POSI 29 V. SIZE 70 NO SD POWER OFF YES V SC 0 V LIN 20 .a.aMOVE....ADJUST RECALL : SET 4-1. Horizontal Position Adjustment · Select H.PHASE item, adjust H.PHASE data value to obtain proper horizontal centering of the internal cross pattern at the left and right of the screen. 4-2. Vertical Position Adjustment · Select V.POSI item, adjust V.POSI data value to center the raster properly on thescreen. 9 ALIGNMENT INSTRUCTIONS 4-3. Vertical Size Adjustment · Select “V.SIZE” item, adjust “V.SIZE” data value to proper vertical size as follows. 5) WHITE BALANCE ADJUSTMENT(S8) · Receive a good local channel. · Enter the service mode and select service adjustment S8. · You can see the OSD as shown in below. RD 58 GD 10 BD 65 RB 105 GB 160 BB 100 .a.aMOVE....ADJUST RECALL : SET · Using volume up or volume down, adjust service adjustment data of RD/GD/BD and RB/GB/BB until a good gray scale with normal whites is obtained.ALIGNMENT INSTRUCTIONS · Press the DISPLAY button to memorize the data. 6) DIGITAL PRESET(D.P) ADJUSTMENTS(S9) SUBBRIGHTNESS ADJUSTMENT · Receive a good local channel. · Enter the service mode and select service adjustment S9. · You can see the OSD as shoown in below. D.P. SUB BRIGHTNESS 64 CONTRAST 10 TINT 27 COLOR 15 .a.aMOVE....ADJUST RECALL : SET 10 ALIGNMENT INSTRUCTIONS · Select Subbrightness item, adjust Subbrightness data value to obtain normal brightness level. · Press the DISPLAY button to memorize the data. CONTRAST · Fixed value = 10 TINT · Fixed value = 27 COLOR · Fixed value = 15 7) FACTORY OUTGOING MODE (S12 : FACT) · If you select the S12, then the set becomes factory outgoing status. · You can see the OSD “outgoing OK” 11 IC DESCRIPTION U-COM(I701) 1 TV ONLY (H) POWER ON(H) 2 CABLE (H) P10 P07 42 P11 P06 41 P12 P05 40 P13/PWM1 P04 39 P14/PWM2 P03 38 P15/PWM3 P02 37 P16 P01 36 P17/PWM P00 35 VSS P73/INT3/TOIN 34 XT1 P72/INT2/TOIN 33 XT2 P71/INT1 32 VDD P70/INT0 31 P84/AN4 P63/SCLK1 30 P85/AN5 P62/SDA1 29 P86/AN6 P61/SCLK0 28 P87/AN7 P60/SDA0 27 RES I 26 FILT BL 25 CVIN B 24 VS G 23 HS R 22 NC 3 ST / MONO AUDIO MUTE(H) 4 AKB WHITE 5 BLUE BACK SOUND RESET H.OUT 6 NC ON(L)/OFF(H) 7 AUTO TINT POWER ON 8 NC ST-BY(H) 9 REMOCON IN 10 NC 11 NC 12 N...
Other models in this manual:Televisions - DTQ-14U1FSP/20U1FSP (4.04 mb)
Televisions - DTQ-14U1FS/20U1FS (4.04 mb)
Televisions - DTQ-14V1FC/20V1FC (4.04 mb)
Televisions - DTQ-14V1FS/20V1FS (4.04 mb)