Votes - 4, Average rating: 3.8 ( )

Manafacture: Fisher File size: 1.09 mb File name: 583b93a2-d828-cca4-c5f7-4f96ef39af5f.pdf Language of manual:

Remove the lower 2 screws on the Lens. (Lower 2 screws are not used.) Slide the lens lock latches to "LOCK" position and lock the lens. (See Figure-4) Connect the lens motor connector to terminal. (See Figure-3) DRIVER IN THE LENS LENS MOUNTING BRACKET Fig-5 LOWER SCREWS -5 5 MOUNT THE LIGHT-BLOCK SHEET AND LIGHT-BLOCK SHEET BASE (See Figure-6) 1. 2. 3. Mount the light-block sheet on the lens as shown LIGHT-BLOCK SHEET BASE in the Figure-6. (In the same position as the removed sheet has been placed). Use the sheet included with the lens. Make sure the part no. and mark (TOP and BACK) on Light-Block Sheet and set them properly. Mount the light-block sheet base included with the lens. UP FRONT CABINET LIGHT-BLOCK SHEET 6 MOUNT THE FRONT CABINET AND LENS COVER (See Figure-6 and 7) LENS COVER Mount the front cabinet with 2 screws. Mount the lens cover. For the cabinet Fig. 1-1, position the marked UP of Lens Cover on top and push in to the front cabinet and turn the Lens Cover fully clockwise until it is properly locked. For the cabinet Fig. 1-3, push the Lens Cover onto the cabinet 1. 2. Fig-7 Fig-6 -6 LENS REPLACEMENT PROCEDURE (FOR "C" TYPE ) Perform the steps 1 to for lens replacement. 6 First set the lens at the fully lower position with lens shift adjustment. LIGHT-BLOCK SHEET BASE FRONT CABINET LENS COVER LIGHT-BLOCK SHEET SCREW "A" LENS COVER FRONT CABINET LENS LOCK 1 REMOVE THE LENS COVER AND FRONT CABINET 1. Turn the lens cover to counter-clockwise and pull it toward front and remove the Lens Cover. 2. Remove 2 Screws-A. 3. Remove the front cabinet 2 REMOVE THE LIGHT-BLOCK SHEET BASE AND LIGHT-BLOCK SHEET 1. Slide the light-block sheet base upward and remove it. 2. Remove the light-block sheet from lens. 3 REMOVE THE LENS 1. 2. 3. Grasp the Lens Lock Lever and turn it fully upward. Remove the Lens into the projector. Disconnect the lens motor lead connector to the socket on the lens attachment. Remove 4 Screws and remove lens attachment. LENS LEVER SCREW Pull the Lens Lock Lever upward - 7 ATTACHMENT SOCKET CONNECTOR LENS MOTOR LEAD - 8 - LENS ATTACHMENT Part No. (610 275 6029) 4 MOUNT THE LENS Remove protective caps (front and back) on the optional lens. Mount the lens on the lens attachment with 4 Screws. Connect the lens motor lead connector to the socket on the lens attachment. (Motor Driven Lens only.) Grasp the Lens Lock Lever and turn it fully upward. Install the Lens into the projector. Turn the Lens Lock Lever fully downward until lever is Locked (clicked position) properly. When installing the Motor Driven Lens, be sure to mount Lens Motor on left-side. After installing the lens, make sure the Lens is not loose and properly installed. 1. 2. 3. 4. Push the Lens Lock Lever fully downward until it is locked (clicked). DRIVER IN THE LENS LENS ATTACHMENT SOCKET CONNECTOR LENS MOTOR LEAD LENS LOCK LEVER LENS LOCK LEVER SCREW When the lens is attached to the projector and images are being projected onto the screen, the peripheral focus may be out of focus in some localized areas. If this happens, insert the spacer in between the lens attachment and the lens to correct the focus. Correcting the focus Spacer "1" Color; Clear 40-inch projection Thickness; 0.1 mm Screen Inserting the spacers corrects the distance for best diagonal focus at the screen. The corrected distance is determined by the thickness of the spacers that are used. As a guide, the distance is adjusted by approximately 30 mm for each 0.1-mm thickness of the spacers. There are three types of spacers provided, and there are four of each spacer type. Use these spacers to correct the distance as required. C D A B Distance Spacer "2" Color; Black Thickness; 0.2 mm Spacer "1" Color; Cream Thickness; 0.3 mm Correction distance 30 mm/for 40-inch projection Correction distance 55 mm/for 40-inch projection Correction distance 80 mm/for 40-inch projection SPACER A B C D A~D Insertion position of the focus correction spacers. Refer to following. Insert spacers in the location A~D (above figure) corresponding to the screen location A~D. Screen UP 5 MOUNT THE LIGHT-BLOCK SHEET AND LIGHT-BLOCK SHEET BASE 6 MOUNT THE FRONT CABINET AND LENS COVER Mount the light-block sheet on the lens. (In the same position as the removed sheet has been placed). Use the sheet included with the lens. Make sure the mark (TOP and BACK) on Light-Block Sheet and set them properly. Mount the light-block sheet base included with the lens. 1. 2. LIGHT-BLOCK SHEET BASE FRONT CABINET LENS COVER LIGHT-BLOCK SHEET Mount the front cabinet with 2 screws. Mount the lens cover. Position the marked UP of Lens Cover on top and push in to the front cabinet and turn the Lens Cover fully clockwise until it is properly locked. 1. 2. UP 5 MOUNT THE LIGHT-BLOCK SHEET AND LIGHT-BLOCK SHEET BASE 6 MOUNT THE FRONT CABINET AND LENS COVER Mount the light-block sheet on the lens. (In the same position as the removed sheet has been placed). Use the sheet included with the lens. Make sure the mark ...

Download now

Please, enter two numbers from picture: