Votes - 4, Average rating: 3.8
(
)
)
|
manual abstract
Then press the ► PLAY button to resume normal playback. 3. «FB button Press the «FB to search backward in DVD mode. 4. »FF buttons Press the »FF to search forward in DVD mode. 5. 0~9 Number buttons Press to select numbers. 6. Direction buttons (▲▼◄►) In the setup menu, press the ▲ ▼ button to select the desired item and press the ◄► button to adjust or set. 7. ENTER button Press to confirm your selection. 8. TITLE button When a DVD disc is playing, press to go to title menu if the disc contains. 9. MENU button (in DVD mode) Press to enter the disc menu in DVD mode. 10. REPEAT button Press to repeat a chapter, track, title or all content in DVD mode. 11. ANGLE button Press to select various camera angles during multi-angle DVD disc playback. 12. A-B button Press to mark a segment to repeat between A and B during DVD disc playback. 13. AUDIO button Press to select audio language during multi-audio language DVD disc playback. 14. Eject button Press to eject the disc out. 15. «STOP button Press to stop playback in DVD mode. 16. MNEXT button Press the wNEXT to skip to the next chapter/track for some discs in DVD mode. 17. mPREV button Press the mPREV to skip to the previous chapter/track for some discs in DVD mode. 18. CARD button Press to shift to USB or CARD mode when there is the input source. 19. SETUP button(in DVD mode) Press to enter the DVD setup menu in DVD mode. 20. SLOW button Press to activate slow playback during DVD disc playback. 21. ZOOM button Press to zoom in or out the picture. 22. GOTO button Press to access or exit the time-searching mode under DVD mode. 23. SUBTITLE button Press to select different subtitle languages during a multiple language DVD disc playback in DVD mode. - 10 - Remote Control Preparation of Remote Control Softly push the back cover to open the battery compartment. Insert two batteries (1.5V, size AAA), please make sure the polarity matches the marks inside the compartment. Softly press the back cover to close it. Using of Remote control Point the remote control unit from no more than about 7m from the remote control sensor and within about 60 degrees of the front of the unit. • Under normal use the battery will last for six months. • Take out battery when the remote is not in use for a long time. The operating distance may vary depending to the brightness around. Notes: Do not point bright lights directly at the remote control sensor. Do not place objects between the remote control unit and the remote control sensor. Do not use this remote control unit while simultaneously operating the remote control unit of any other equipment. - 11 - System Connections Do not connect the power cord until all other connections have been made. Ensure that you observe the color cord when connecting audio and video cables. Connecting to External AV Signal Source Use the audio and video cable to connect the AV input jacks on the rear panel of the unit to the external AV signal source. Use the S-VIDEO cable to connect the S-VIDEO input jack on the rear panel of the unit to the external AV signal source. After connection, turn on the power of the unit and the external AV signal source and then press the SOURCE button to shift to CVBS or S-VIDEO mode. Note: the L/R audio input jacks can be used in the both CVBS and S-VIDEO modes. - 12 - System Connections Connecting to External AV Signal Source YPbPr Use the audio and video cables to connect the Y/Pb/Pr input Jacks on the rear panel of the unit to the external AV signal source. After connection, turn on the power of the unit and external AV signal source and then press the SOURCE button to shift to Component mode. - 13 - System Connections Connecting to External AV Device (AV Out) The unit supports audio and video signal input function, it can be connected to the external audio and video device. Use the audio and video cables to connect the AV output Jacks on the rear panel of the unit to the external AV input device. - 14 - System Connections Connecting to PC The unit can be connected to PC (personal computer) via the VGA cable. Follow the steps and the figure below to connect: 1. Connect one end of the VGA cable to the VGA input jack on the rear panel of the unit. 2. Connect the other end to the PC. 3. Connect one end of the audio cable to the PC audio input jack on the rear panel of the unit. 4. Connect the other end to the PC audio output jack. 5. The resolution should be set to the PC’s resolution at 1024x768@60Hz After connection, turn on the unit and the PC and then press the SOURCE button to shift to VGA mode. - 15 - System Connections Connecting to Earphones This unit can be connected to an earphone for listening to music privately. See the below figure for details: After connecting to the earphone, the internal speakers output will turn off automatically. Connecting to Power Adapter Power is supplied through the provided power adapter, one en...