Votes - 4, Average rating: 3.8
(
)
)
|
manual abstract
in TV modeOn-screen menus To select TV programme number To select between analogue and digital TV, or an external source Picture format To exit Menus To alter the volume To call up text services in interactive services in analogue mode.digital When using menus the direction buttons move the cursor on the screen up, selection To change programme positions and teletext pages Select to control your Toshiba TV, DVD or VCR No function on-screen digital Programme Guide To display on-screen information Selectable picture mode down, left or right. to confirm yourOK When in TV mode: Still picture Stereo / bilingual transmissions SUBTITLE SUBTITLE Digital Subtitles When using the Programme Guide BACK Time display in analogue mode -2 hours +2 hours -24 hours +24 hours Inserting batteries and effective range of the remote Remove the back cover to reveal the battery compartment and make sure the batteries are inserted the right way round. Suitable battery types for this remote are AAA, IEC R03 1.5V. Do not combine a used, old battery with a new one or mix battery types. Remove dead batteries immediately to prevent acid from leaking into the battery compartment. Dispose of them in a designated disposal area. Warning: Batteries must not be exposed to excessive heat such as sunshine, fire or the like. The performance of the remote control will deteriorate beyond a distance of five metres or outside an angle of 30 degrees from the centre of the television. If the operating range becomes reduced the batteries may need replacing. English -4 Connecting external equipment Before connecting any external equipment, disconnect from the main power. English -5 English - 6 - Aerial cables: Connect the aerial to the socket on the rear of the television. If you use a decoder and/or a media recorder it is essential that the aerial cable is connected through the decoder and/or through the media recorder to the television. SCART leads: Connect the media recorder IN/OUT socket to the television. Connect the decoder TV socket to the television. Connect the media recorder SAT socket to the decoder MEDIA RECORDER socket. Before running APS (AUTO PROGRAMMING SYSTEM) put your decoder and media recorder to Standby. A wide variety of external equipment can be connected to the back of the television, therefore the relevant owners manuals for all additional equipment must be referred to. If connecting S-VIDEO equipment, set the INPUT for S-Video. See page 24. If the television automatically switches over to monitor external equipment, return to normal television by pressing the desired programme position button. To recall external equipment, press to select between TV, EXT1, SVideo, PC, YPBPR, DTV or HDMI. Connecting external equipment continued, Connecting the PC via PC input • Power off both computer and TV before making any connections. • Connect the PC cable to the PC input of your TV and to the 15-pin connector on the rear of your computer. • Tighten the screws on the plugs until the connectors are fastened securely. • For PC sound, use stereo jack socket located at the rear side of the TV. High Definition Your TV is capable of displaying High Definition pictures from devices such as a High Definition Satellite Receiver or DVD Player. These devices must be connected via the HDMI socket or YPbPr (Component) sockets. These sockets can accept either 720p or 1080i signals. PLEASE NOTE: • Although this television is able to connect to HDMI equipment, it is possible that some equipment may not operate correctly. • HDMI cables should be less than 5m. • It is recommended that approved HDMI cables up to 5m long is used. If the unit has DVI output, a special conversion cable from DVI to HDMI will be required. HDMI, the HDMI logo, and High Definition Multi Media Interface are trade marks, or registered trade marks of HDMI licensing, LLC. English - 7 - Connections and controls Whilst all the necessary adjustments and controls for the television are made using the remote control, the buttons on the top of the television may be used for some functions. Switching on If the standby LED is unlit, connect the mains plug to the mains outlet. Press the Power button to switch the television into standby. The blue LED will light. To view the television, press or any of the number buttons on the remote control, or the P+ / P- buttons on the TV. The blue LED will turn off and the picture will appear after a few seconds. To put the television into standby, press on the remote control, the blue LED will light. Using the remote control Press the MENU button on the remote control to see the menus. In TV mode the menu appears as a group of icons each for a menu option. Press the Up or Down button to select a topic. To use the options press the Right or OK buttons on the remote control to select. Use the Up and Down buttons to select the required choice. Follow the on screen instructions. The functions of each menu are described in detail throughout the manual. Using the c...