Votes - 3, Average rating: 3.3 ( )

Manafacture: Pyramid Technologies File size: 809.85 kb File name: Language of manual:

To prevent this, connect one end of a shield wire to the amplifier's ground screw (on rear panel). Then connect the other end of this wire to the ground terminal on the mixer or preamplifier enclosure. PREAMP OR MIXER Input connections These amplifiers accept a board range of input sources, including Compact Disc (CD,DVD) Cassette, Reel· to· Reel or other tape players; Tuners; Equalizers; Signal Processors. Connecting a CD, DVD, tape player or tuner In a normal installation, one would use the RCA JACKS for connecting a CD player, DVD player,tape player or tuner. 2 -PYRAMID PA·600DJ/800DJ/l000DJ/2000DJ Amplifier OWner's Manual Connecting an equalizer or external signal processor Connect the processor's OUT to the amplifier's IN connector. use XLRl6.35 mm combo jacks use XLRl6.35 mm combo jacks Stereo or Mono Inputs Your Pyle Pro amplifier can be operated in Stereo, Mono or Bridged mode, depending on the input source. If the input signal is mono, slide the Stereo/Mono/Bridged selector switch to MONO and the signal will be routed through both channels. If you wish to run the amplifier in bridged output mode, slide the switch to Bridged. connections can connect 4 Ohm, 8 Ohm or 16 Ohm speakers to Channell and/or Channel 2 of the amplifier. If you connect two pairs of speakers, be sure to follow these guidelines: • Speakers which are connected to the same channel are part of a pair, and must be of the same impedance. • Speakers connected to different channels are NOT part of a pair, and can be of different impedances. 1. Prepare the wire by removing about 1 inch of insulation from end of the speaker wire you intend to connect to the amplifier. Then twist the exposed wire to secure all the wire strands. NOTE: Use 16-gauge speaker wire for lengths up to25 feet; 14-gauge wire for lengths over 25 feet. It is recommended that you use the shortest length of wire possible. 2. Connect the wires to the speaker's positive and negative NOTE: Most speaker terminols are either color-coded or have a mark that indicates the terminal's Usually positive terminals are red or have a (+J, and negative terminols are black or have a minus symbol (-J. 3. Connect the speaker wires to the amplifier's left and right speaker terminals according to the terminal color polarity. STEREO OPERATION SWITCH IN "STEREO" POSITION CH 1 ..g STEREO SIGNAL SOURCE CAUTIONI Do not use balanced and unbalanced inputs simultaneausly!! V'V'CH 2 -++ -CH 1 ..g STEREO SIGNAL SOURCE CAUTIONI Do not use balanced and unbalanced inputs simultaneauslyll MONO OPERATION SWITCH IN "MONO" POSITION USE MONO SIGNAL SOURCE CHANNEL1 CAUTION! Do nat use balanced and unbalanced inputs simultaneouslyll USECHANNEL 1 INPUT ONLY CAUTION! Do not use balanced and unbalanced inputs simultaneously!! Bridged Mode Operation .This amplifier can operate in a mono bridged output mode, If your speakers can handle the following power output levels: As shown in the diagram below, connect the speaker's positive (+) to the amplifier's red speakers left (112) terminals and negative (-) to red speakers right (1/2) terminals. The speaker (+) on the amplifier is used as a negative (-) terminal for a connection. MONO BRIDGED OPERATION SWITCH IN "BRIDGED" POSITION DO NOT USE -+ USECHANNEL 1 INPUT ONLY BLACK TERMINALS CAUTIONI Do not use balanced and unbalanced inputs simultaneouslyll MONO SIGNAL SOURCE USECHANNEL 1 INPUT ONLY CAUTIONI Do not use balanced and unbalanced inputs simultaneously!! ] -PYRAMID PA-600DJ/800DJ/l000DJrlOOODJ Amplifier OWner's Manual Connecting to standard AC power After makin.. all other connections, set the POWER switch to OFF positIon. Then connect the power cord to a standard AC outlet. the amplifier This is designed to accept standard rack mounting installations. Two slots on each end of the front panel make it suitable for such an installation. secure four mounting screws (not supplied) through these slots and into your standard electronics equipment rack. Turning the amplifier on 1. Tum on the audio inp'ut source equipment which is connected to the amplifier INPUT jacks. 2. Set the amplifier's Channell and Channel 2 output level gain controls to the minimum level settings. 3. Push in the power switch to turn the amplifier on. Using the power LED meters (WIthout PA-600DJ) The meter pointer position indIcates the amplifier output power. For ease of reading in dark environments, the meter IS illuminated. Caring for your Pyramid PA Amplifier Your Pyramid PA Amplifier is an example of superior design and craftsmanship. The following suggestions will help you care for your amplifier so you can enjoy years of use: • Keep the dry. If it wet, immediately. • Use the only in installations. • Handle the amplifier gently and do not dropl • Keep the amplifier away from dust and • Wipe occasionally with a damp cloth to it looking new. Do not use harsh chemicals, or detergents! Using the Channel 1 and Channel 2 Output Level controls Rotate output level gain clockwise to increase, or cou...

Download now

Please, enter two numbers from picture: