Votes - 3, Average rating: 3.3
(
)
)
|
manual abstract
Press again to turn the TV off. 2. Direct Channel Selection Buttons (0-9) - Allows direct access to any channel. 3. QUICK VIEW Button - This button allows you to go back to the previous channel selected by just pressing the QUICK VIEW button. Press this button again to return to the channel you were watching. 4. SLEEP Button - To set the TV to turn off after a preset amount of time, press the SLEEP button on the remote control. The clock will count down 10 minutes each time the button is pressed in the order of 120, 110, 100,...... 20, 10, 0. After the sleep time is programmed, the display will disappear then reappear momentarily every ten minutes to remind you the sleep timer function is operating. To confirm the sleep time setting, press the SLEEP button once and the remaining time will be momentarily displayed. To cancel sleep time, press the SLEEP button repeatedly until the display turns to 0. 5. VOL (VOLUME) (, / > Buttons - Press the > button to increase, or the < button to decrease the volume level. 6. MENU Button - Press to display the On-Screen menu function. 7. SET - / + Buttons - Press to select the desired setting during On-Screen operations. 8. RESET Button - Press to reset the On-Screen picture. Press to reset a password in the V-CHIP Password setting mode. 9. TV/AV Button - Switches between TV and external inputs. 10. CALL Button - When you press this button, the channel number will appear in the upper right corner of the screen. Press the button again to remove display from the screen. 11. MUTE Button - To turn off the sound, press this button once. The TV will be silenced and the symbol “MUTE” will appear on the screen. The muting feature can be released by pressing the MUTE button again or one of the VOL > or < button. 12. CH (CHANNEL) ^ / v Buttons - Press the button to change to a higher numbered channel set into memory. Press the v button to change to a lower numbered channel set into memory. 13. ENTER Button - Press to enter or select information for OnScreen operations. 14. AUDIO SELECT Button - Switches sound between mono and stereo when receiving broadcasts in stereo or SAP. 15. CH.1/2 Button - Switches between Channel 1 and Channel 2 in the Closed Caption mode. 16. TV/CAP/TEXT Button - Press this button to switch between normal TV and the two Closed Caption modes (captions and 1/2 of full screen text). Closed Captioning will display text on screen for hearing impaired viewers. Before using the remote control, batteries must first be installed. HOW TO INSTALL BATTERIES Use two “AAA” size batteries. The batteries may last 1. Open the battery compartment cover. ^praxrnatety °ne year dependng °n h°w much the i-emote control is used. For best performance, it is recommended that batteries should be replaced on a yearly basis, or when the remote operation becomes erratic. Do not mix old and new batteries or different types. BATTERY PRECAUTIONS These precautions should be followed when using batteries in this device: • Use only the size and type of batteries specified. • Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to the device. • Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones. • If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage. • Do not try to recharge batteries not intended to be recharged; they can overheat and rupture (Follow battery manufacturer's directions). 5 2. Install two “AAA” batteries (not supplied). 3. Replace the battery compartment cover. 1/21/05, 9:21 AM 3U10421A-E 5 ENGLISH I I I I I ANTENNA/CATV CONNECTIONS Combination VHF/UHF Antenna Single 75 ohm Cable . a n=s 300 ohm Twin-lead Wire Splitter '=[ UHF Antenna 300 ohm Twin-lead Wire fa VHF Antenna Single 75 ohm Cable Take off the Splitter 300-75 ohm Matching Transformer (not supplied) 300 ohm Twin-lead Wire Combiner (not supplied) Incoming CATV 300-75 ohm Matching Transformer (not supplied) =| Converter/ Descrambler |= i □- Converter/ Descrambler Splitter A / B Switch [A^b Combination VHF/UHF Antenna (Single 75 ohm Cable or 300 ohm Twin-lead Wire) Connect the 75 ohm cable from a combination VHF/UHF antenna to the Antenna Jack. If your combination antenna has a 300 ohm Twin-lead Wire, use the 300-75 ohm Matching Transformer (not supplied). Combination VHF/UHF Antenna (Separate VHF and UHF 300 ohm Twin-leads) Connect the UHF Twin-lead Wire to a Combiner (not supplied). Connect the VHF Twin-lead to the 300-75 ohm Matching Transformer (not supplied). Attach the Transformer to the Combiner. Attach the Combiner to the Antenna Jack. This television has an extended tuning range and can tune most cable channels without using a cable company supplied converter box. Some cable companies offer “premium pay channels” i...