Votes - 2, Average rating: 4
(
)
)
|
manual abstract
The Gefen 4x CAT6 Extender for HDMI supports HDMI 1.3 features such as 1080p Full HD and multichannel audio formats including Dolby TrueHD and DTSHD Master Audio. The Gefen 4x CAT6 Extender for HDMI digital transmission method insures 100% signal integrity over this single cable extension solution. With IR Back Channel and RS-232 support, control of the 4x4 Matrix and Hi-Def sources, at any of the 4 individual zones, is at your fingertips. Each Receiver unit allows control for Matrix switching and sending IR commands back to the source located up to 200 feet (60 meters) away. The 4x CAT6 Extender for HDMI adds IP Control to the connected Gefen 4x4 Matrix for convenient access to switching and routing of the connected sources using a web browser. How It Works The Gefen 4x CAT6 Extender for HDMI can be connected in two ways : 1) Matrix Mode: As a Control and Extender system for any Gefen 4x4 Matrix unit. Extend up to 4 of the Gefen 4x4 Matrix outputs up to 200 feet (60 meters) away with IR, RS-232, or IP Control at any of the remote locations. Also supports the IR Back Channel for remote control of the extended Hi-Def sources. 2) Stand-alone Mode: As a stand-alone Extender system. Connect up to 4 Hi- Def sources to any of the available inputs. Simply extend the connected Hi-Def sources up to 200 feet (60 meters) with IR Back Channel. 1 OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE 4X CAT6 EXTENDER FOR HDMI • CAT-6a cables can be used up to 200 feet (60 meters). • Shielded (STP) CAT-6a is recommended. However, unshielded (UTP) CAT-6a is acceptable. NOTE: Shielded cable has an advantage by providing immunity to Electromagnetic Interference (EMI), cell phones and A/C motors. 2 FEATURES Supported HDMI 1.3 Features • 225 MHz (up to 12 bit YUV 444 @ 1080p) • Deep Color • Dolby TrueHD and DTS-HD Master Audio • Lip-Sync • CEC Pass-Through Features • Extends HDMI 1.3 at 1080p up to 200 feet (60 m) • Extends DVI at 1920x1200 up to 200 feet (60 m) when using a passive HDMI-to-DVI adapter. • 3DTV Pass-Through • Color Space Conversion • IR Remote Control • Built-in IR Extender and IR Back Channel • RS-232 serial control • IP Control (Sender unit feature) • Audio and video are transmitted digitally for zero signal loss • Supports multichannel digital audio formats including Dolby TrueHD and DTS-HD Master Audio • Metal enclosure provides better RF shielding • Compensation for cable skew • Maintains settings on Power-On state Package Includes (1) 4x CAT6 Extender Sender Unit (4) 4x CAT6 Extender Receiver Units (4) 1 ft. HDMI Cables (M-M) (1) RS-232 Serial Cable (M-F) (1) 24V DC Power Supply (4) 5V DC Locking Power Supplies (1) Set of Rack Ears (Sender Unit Only) (1) User Manual 3 SENDER PANEL LAYOUT Front Panel 1 23 Back Panel 45678 9 10 4 SENDER PANEL DESCRIPTIONS 1 Standby Button Sets the 4x CAT6 Extender for HDMI into Standby Mode. 2 IR Sensor Receives signals from the IR Remote Control. 3 Power Indicator This LED will turn bright red once the locking power supply has been properly connected. 4 IR Blaster (4) Used to connect the IR Blaster to the Source device. 5 CAT6 Output Jack (4) Connects the Sender unit to the Receiver unit using CAT-6. 6 RS-232 Serial Port (Input) The 4x4 Matrix may be switched remotely using serial communications with any office computer or a control automation device by connecting to this port. Please see page 20 for details. 7 Locking HDMI Port (4) Connect a HI-Def source to this HDMI port. 8 IP Control Connect to this port to control the 4x CAT6 Extender for HDMI using IP Control. See page 25 for more information. 9 RS-232 Serial Port (Output) Connects to the RS-232 control device. The 4x4 may be switched remotely using this port. See page 20 for details. 10 24V DC Power Connector Connects the included 24V DC power supply to this receptacle. 5 RECEIVER PANEL LAYOUT Front Panel 1 234 5 Back Panel 678 910 6 RECEIVER PANEL DESCRIPTIONS 1 Control Buttons When connected to any 4x4 Matrix for HDMI, these remote buttons on the Receiver unit can switch between the 4 Hi-Def inputs connected to the 4x4Matrix for HDMI. 2 IR Sensor Control the Receiver unit by pointing the IR Remote Control to the IR Sensor. 3 EQ Trimpot Used to equalize the signal to compensate for distance and skew variations found in various brands of CAT-6 cable. 4 Input Indicators (HDMI In 1 - HDMI In 4) An LED will Displays the current input of the 4x4 Matrix. 5 Power Indicator This LED will turn bright red once the power supply has been properly connected. 6 IR Extender Port Used to extend the IR Sensor range of the Receiver unit. 7 CAT6 In Connector Connect the CAT-6 cable from the Sender unit to the RJ-45 connector. 8 HDMI Out Connect the HDMI cable from the HDTV display to the HDMI Out. 9 RS-232 Input Connects a controlling device to this port. 10 5V DC Locking Power Connector Connects the included 5V DC Locking Power Supply to this receptacle. 7 IR REMOTE DESCRIPTION RMT-4-IR Remote (Optional) 1 2 1 Activity...