Votes - 2, Average rating: 4 ( )

Manafacture: Mitsubishi Electronics File size: 5.3 mb File name: faf8450d-78b8-1c34-51fa-764fd1c57a6e.pdf Language of manual:

This input supports 480i, 480p, 720p and 1080i video formats. It is not intended for use with personal computers or devices outputting video signals with computer resolutions. This input can also be used as a DVI connection with separate analog audio inputs. An optional HDMI-to- DVI adaptor or cable will be necessary to make this connection and may be available from your local electronics retailer. When using the optional HDMI-to- DVI adapter, the DVI analog audio inputs on your TV allow you to receive left and right audio from your DVI device. This input is HDCP (High-Bandwidth Digital Copy Protection) compliant. 11. M-Link/RS-232C Control A digital control interface that works in conjunction with M-Link. While M-Link provides the digital video signal, the RS-232 control provides enhanced functioning such as automatic power ON/OFF and input port selection with an external control system. For RS-232 command protocol please visit 12. Digital Audio Output This output will automatically send Dolby® Digital audio from digital channels and IEEE 1394 devices to a digital Audio/Video receiver. Connect this output to the A/V receiver’s coaxial digital audio input. The output will automatically turn off when viewing an analog channel or device. Use Monitor Output Audio 2 to send analog sound to your A/V receiver. Some digital cable channels send MPEG-1 digital audio instead of Dolby Digital, however, not all A/V receivers can decode MPEG-1 digital audio. This can cause the A/V receivers to produce a loud noise that can damage speakers. For this reason, the TV will automatically turn off the digital audio output when tuned to a channel or device that has MPEG-1 digital audio and send it to the A/V receiver as analog left and right audio from Monitor Output. 2 Connecting External Devices & NetCommand® Setup16 Wall Outlet Cable or Cable Box17 CableCARD™ Technology18 Single Lead Antenna19 Separate UHF and VHF Antennas 19 VCR Video and Audio to an Antenna or Wall Outlet Cable20 VCR Video and Audio to a Cable Box21 A/V Receiver or Stereo System22 Satellite Receiver or Other Device with S-Video22 DVD Player with Component Video23 Computer with a PC Monitor Output23 DTV Receiver with Component Video24 with RGB, HV Video 25 M-Link Control, RS-232 Connection26 HDMI Device26 DVI Device26 IR Emitter NetCommand®27 Compatible IEEE 1394 Devices28 Helpful Hints30 Connecting External Devices & NetCommand® Setup NetCommand is able to control many current audio and video devices by sending remote control signals from the TV to each device through IR emitters. Additionally, it is also able to learn the remote control signals used by most audio video devices not already in the TV’s memory. NetCommand can automatically switch the TV and compatible or learned Audio/Video (A/V) Receivers to the correct input used with each device. It is important that the inputs on the TV and A/V receiver back panels match the NetCommand setup that is displayed on-screen. To simplify the installation of NetCommand, there is a step-by-step on-screen NetCommand Setup procedure in this chapter, which details the type and brands of devices you are connecting to the TV. The NetCommand Setup also assigns preset TV and A/V receiver inputs for each device. You should connect each device to the TV input (both audio and video) and to the A/V receiver (audio) as shown in the figure below. AVReceiverTVDevicetobeconnectedstereoand/ordigitalaudiocablesvideoandstereoaudiocablesstereoanddigitalaudiocables IREmitters The following charts show which preset inputs you should use on the TV and A/V receiver. Chart 1 shows TV inputs. Chart 2 shows the A/V receiver inputs used by A/V receiver models already known by NetCommand. Chart 1 Device Audio and Video Outputs to TV Inputs Cable for CableCARD™ Service ANT-1 Antenna/Cable (digital/analog) ANT-1 if primary viewing source, ANT-2 if secondary viewing source Cable box ANT-2 VCR Input-1 Satellite Receiver (DBS) Input-2 Camcorder Input-3 (on front panel) DVD Player Component-1 ModelM-VR800& M-VR1000ModelM-VR900& M-VR700ModelLifestyle®28ModelAVR-2700ModelDTR-9.1ModelVR-2080ModelSR8200ModelVSX-D557ModelVSX-49TXModelRSX-1065ModelSTR-DE825ModelRV-X2095ModelRX-V2200DeviceAudioOutputtoAVReceiverInputsbyNameVCRVCR1VCRVCRVCR-1Video1Video1VCR1VCR/TapeVCR1/DVRVideo2Video1VCR1VCR1SatelliteReceiverAuxCable/DBSAUXCDVideo3Video3DSSCDSATVideo4TV/DBSTV/DBSD-TV/LDDVDPlayerDVDDVD(built-in)DVDVDPDVDVideo4DVDLD/SATDVD/LDVideo5TAPE/MDCDDVDTVMonitorOutput(&DigitalAudio) TVTVTVTV/DBSVideo4Video4TVDVD/TVTVVideo1DVD/LDDVD/LDCBL/SATChart2Mitsubishi1Mitsubishi2BoseDenonIntegraKenwoodMarantzPioneer1Pioneer2RotelSonyYamaha1Yamaha2 After using NetCommand Setup, you may go to the NetCommand menu at any time to change the inputs you used for connecting each device, custom name devices, add devices not included in the presets above or delete devices no longer used. See Edit NetCommand. See Helpful Hints, at the end of this chapter for addi...

Download now

Please, enter two numbers from picture: