Votes - 2, Average rating: 4 ( )

Manafacture: Samsung File size: 10.03 mb File name: Language of manual:

(reconnect AC cord and wait until cable box reboots. It may take up to 20 minutes.) • Set output resolution of cable box to 1080i or 720p. Sound Quality First of all, please perform the Sound Test to confirm that your TV audio is properly operating. • Go to MENU - Support - Self Diagnosis - Sound Test If the audio is OK, the sound problem may caused by the source or signal. No sound or sound is too low at maximum volume. • Please check the volume of external device connected to your TV then, adjust the TV volume accordingly. Picture is good but no sound. • Set the Speaker Select option to TV speaker in the sound menu. • Make sure audio cables from an external device are connected to correct audio input jacks on the TV. • Check connected device’s audio output option. (ex: You may need to change your cable box’ audio option to HDMI when you have HDMI connected to your TV.) • If you are using a DVI to HDMI cable, a separate audio cable is required. • Deactivate SRS function if you are setting the volume over 30 value. • Remove plug from headphone jack. (if available on your TV) Noise from speaker. • Check cable connections. Make sure a video cable is not connected to an audio input. • For Antenna/Cable connection, check signal strength. Low signal level may cause sound distortion. English - 43 Issue Solution No Picture, No Video TV won’t turn on. • Make sure the AC power cord is plugged in securely to the wall outlet and the TV. • Make sure the wall outlet is working. • Try pressing the PoWER button on the TV to make sure the remote is working properly. If the TV turns on, it may be caused by Remote Control. To fix the Remote problem, refer to ‘Remote control does not work’ below. TV turns off automatically. • Check if the Sleep Timer is set to on in the Setup menu. • If connected the TV to your PC, check your PC power settings. • Make sure the AC power cord is plugged in securely to the wall outlet and the TV. • If there is no signal for about 10 ~ 15 minutes with Antenna/Cable connection, the TV will turn off. No picture/Video. • Check cable connections.(remove and reconnect all cables of TV and external devices) • Set your external device’s (Cable/Set top Box, DVD, Blu-ray etc) video output to match the connections to the TV input. For example, external device’s output: HDMI, TV’s input: HDMI. • Make sure your connected device is powered on. • Make sure to select the TV’s correct source by pressing the SoURCE button on the TV remote. RF(Cable/Antenna) Connection Cannot receive all channels. • Make sure Antenna cable is connected securely. • Please try Plug & Play to add available channels to the channel list. Go to MENU -Setup - Plug & Play and wait for all avaiable channels are stored. • Verify Antenna is positioned correctly. Picture is distorted: macroblock, small block, dots, pixelization • Compression of video contents may cause picture distortion especially on fast moving pictures such as sports and action movies. • Low signal level can cause picture distortion. This is not a TV issue. PC Connection ‘Not Supported Mode’ message. • Set your PC’s output resolution and frequency so it matches the resolutions supported by the TV. PC is always shown on source list even if not connected. • This is normal; PC is always shown on the source list even though a PC is not connected. Video is OK but there is no audio with HDMI connection. • Check the audio output setting on your PC. English - 44 Issue Solution Others Picture is not shown in full screen. • Black bars on each side will be shown on HD channels when displaying upscaled SD (4:3) contents. • Black bars on Top & Bottom will be shown on movies that have aspect ratios different from your TV. • Adjust picture size option on your external device or TV to full screen. Remote control does not work. • Replace the remote control batteries with correct polarity (+ -). • Clean the transmission window located on the top of the remote. • Try pointing the remote directly at the TV from 5~6 feet away. Can not control TV power or volume with Cable/Set top box remote control. • Program the Cable/Set top box remote control to operate the TV. Refer to Cable/Sat user manual for SAMSUNG TV code. ‘Not Supported Mode’ message. • Check the supported resolution of the TV and adjust the external device’s output resolution accordingly. Refer to resolution settings in this manual. Plastic smell from TV. • This smell is normal and will dissipate over time. TV Signal Information is unavailable in the Self Diagnostic Test menu. • This function is only available with digital channels with an Antenna (RF/Coax) connection. TV is tilted to right or left side. • Remove the stand base from TV and reassemble. Can not assemble stand base. • Make sure TV is placed on flat surface. If can not remove screws from TV, please use magnetized screw driver. Channel menu is grey out. (unavailable) • Channel menu is only available when TV source is selected. Your setti...

Download now

Please, enter two numbers from picture: