Votes - 1, Average rating: 4
(
)
)
|
manual abstract
The following section of this manual will focus on operation method of the remote control. (2)The figures shown in this manual may be somewhat different from the actual situation, please reference to the practicality. 2 INTRODUCTION (continued) Control Buttons (continued) remote control o- -POWER HD/TV MODE PICTURE MODE- DISPLAY PROGRAM UP MUTE MENU VOLUME DOWN DOUBLE VIEWING' RECALL- 0-9 NUMERIC PIP AV/TV-PIP CHANNEL UP- PIP CHANNEL DOWN-PIP STILL- _RECALL_. ¿7 TIMEI -O CZf a CH- a DVI/TV MODE PC/TV MODE SOUND MODE STILL/MOVABLE PICTURE MWIN NOT AVAILABLE EXIT VOLUME UP TV/AV PROGRAM DOWN -TIMER -PIP ON/OFF "PIP LOCATION -PIP SIZE -PIP SWAP Note: The button design and specifications of the remote control are subject to change without notice. 3 INSTALLATION To Install the projection TV • Please read the PRECAUTIONS completely before installation. • It is recommended to watch projection TV in soft and indirect light and face center of the screen for optimum viewing effect. • Allow enough space (at least 10cm) between the projection TV and the other subject for proper • Avoid excessively warm or wet locations to prevent possible damage to the cabinet or components. Keep proper watching distance. 10cm After installation, plug the projection TV in the supply socket. 4 INSTALLATION To Connect the Antenna An outdoor antenna or CATV is recommended for the best reception. The antenna type and its location differ dependent on local conditions. 300il TWIN-LEAD FEEDER 75il/300il CONNECTOR Outdoor antenna Notes: ® It is recommended that a 75il coaxial cable be used in order to eliminate possible interference and noise which may occur due to nearby radio transmissions. (2) When using a 30011 twin-lead feeder, connect it to a 300il/75il converter and insert the converter into the projection TV's ANTENNA IN terminal. (3) Connect an outdoor antenna referring to the above figure. Set up a lightning arrester and check it regularly when an outdoor antenna is used. @ The antenna cable should not be tied together with other wiring. 5 INSTALLATION Replacing the Lamp The lamp used in a projection TV has a limited lifespan. It should be replaced when the screen becomes darker, less clear, has no effect after image adjusted or the lamp doesn't work. Please replace the lamp with operation manual's guide. (Note: You'd better refer the servicing to qualified service personnel of Dealer.) After replacing the lamp, as the screen quality will be bright and clear as new. To replace the lamp, please follow these steps: ® Unplug TV, then use a screwdriver to remove the lamp cover. ŒT Use a screwdriver to unfasten 3 screws securing the lamp and separate the lamp from the engine. (Unfasten the screws is ok) Put in the new lamp and lock the screws securing the lamp. @ Fix the lamp cover. ~(T) ^ The lamp must be the same code number and type avoiding damage of TV. ^ Turn the power off and wait for 30 minutes before replacement. ^ Do not touch the glass part of the lamp to avoid injuring by sudden break; do not place the old lamp within the reach of children. ^ Please note that when indicator II turns red, it means the lamp doesn't work well. Specify by a table on page 10. 6 INSTALLATION (continued) To Install Remote Batteries 1. Remove the battery cover. 2. Place in two AAA batteries. Make sure the positive 0 and negative 0 polarities are correct. vy -battery cover ^ To avoid battery leakage, remove batteries from the remote control when it is not to be used for a long period of time or the batteries are exhausted. ^ Do not expose batteries to fire or disassemble them. •Caring for the remote control ^When in operation, please point the remote control directly to the center of the projection TV screen. XDo not repeatedly press the buttons on the remote control too quickly. ^Do not expose the remote control to impacts, water or disassemble it. 7 BASIC BUTTONS Power To enter or exit standby mode, press POWER on the remote control. Standby function enables you to reduce power consumption and damaging to the lamp. ^Don't leave your projection TV in standby mode for a long time, turn the power off when left unattended for a long period of time. Numeric buttons _0 _q CZ>~ C2? Press the Numeric buttons to enter po-sition number respectively. ^TV will switch to the channel number you chose without pressing on other numeric buttons in 3 seconds. ^The set has 0-235 programs preset. P-/+.V-/+ Press P-/+ to select a lower or upper position number. Press V-/+ to decrease or increase volume. 8 BASIC BUTTONS (continued) DISPLAY DISPLAY Press DISPLAY to display the current position number and time settings. 00:00 ^Time display is available only after you adjust the Timer. RECALL _ЛЕО C2> Press RECALL repeatedly to switch the projection TV between the current program position and previous program position. MUTE MUTE D Use the MUTE function to disable the s...