Votes - 2, Average rating: 3
(
)
)
|
manual abstract
22. Heat-This TV product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. PREPARATION FOR USE 3) Press the VOL(ume) ^ button so that "ADD/DELETE" is selected. 4) Use the CH(annel) Ў or ^ button to select the channel you wish to put into memory or to erase from memory. Note: The display will disappear automatically in about 10 seconds. Perform "ADD/DELETE" function while this display appears on the screen. ADD/DELETE AUTO PRESET CH . Press the VOL(ume) Ў or ^ button to light up the channel number in LIGHT BLUE if you wish to add the channel into memory. . Press the VOL(ume) Ў or ^ button to light up the channel number in LIGHT RED if you wish to erase the channel from memory. 5) Press the MENU button to exit the menu. MTS (Multi-Channel Television Sound) SYSTEM You can listen to a program in MTS stereo by following the steps below. To show the status, press the DISPLAY button on the remote control. Type of broadcast Regular -None- Stereo broadcast STEREO SAP Menu Selection MAIN MONO SAP -None--None- MONO STEREO SAPMAIN MAIN SAP: Second Audio Program, which means your program can also be received in a second language or sometimes a radio station. [To Select STEREO, MONO or SAP in Stereo broadcast] 1) Press the MENU button so that the menu display appears on the TV screen. 2) Press the CH(annel) Ў or ^ button to point to "TV SOUND". 3) Press the VOL(ume) Ў or ^ button to select your desired stereo mode. ([MAIN], [MONO] or [SAP].) : Press the VOL(ume) Ў or ^ button. PICTURE CHANNEL SET [ENG] / ESP / FRA V-CHIP SET UP CAPTION [OFF] TV SOUND [MAIN] PICTURE CHANNEL SET [ENG] / ESP / FRA V-CHIP SET UP CAPTION [OFF] TV SOUND [MONO] PICTURE CHANNEL SET [ENG] / ESP / FRA V-CHIP SET UP CAPTION [OFF] TV SOUND [SAP] RESUME FUNCTION If the power fails or is disconnected while the TV is powered on, the TV will turn on automatically when the power resumes. LANGUAGE SELECTION If you want to change the language of the on-screen menu, follow the procedure below. 1) Connect the power cord to a standard AC outlet. Note: If some digits appear in the corner of the screen, press the POWER button without unplugging the power cord. 2) Press the POWER button to turn on the TV. 3) Press the MENU button so that the menu display appears on the TV screen. 4) Press the CH(annel) Ў or ^ button to point to "[ENG]". 5) Select "ENG(lish)", "ESP(anol)" or "FRA(ncais)" by using the VOL(ume) Ў or ^ button. 6) Press the MENU button to exit the menu. PICTURE CHANNEL SET [ENG] / ESP / FRA V-CHIP SET UP CAPTION [OFF] TV SOUND [MAIN] PICTURE CHANNEL SET [ENG] / ESP / FRA V-CHIP SET UP CAPTION [OFF] TV SOUND [MAIN] CHANNEL PRESETTING ADD/DELETE AUTO PRESET CH PICTURE CHANNEL SET [ENG] / ESP / FRA V-CHIP SET UP CAPTION [OFF] TV SOUND [MAIN] To preset a channel or to change a preset channel, follow the procedure below. 1) Press the POWER button to turn on the TV. 2) Press the MENU button so that the menu display appears on the TV screen. 3) Press the CH(annel) Ў or ^ button to point to "CHANNEL SET". Then, press the VOL(ume) ^ button. 4) Press the CH(annel) Ў or ^ button to point to "AUTO PRESET CH". Then, press the VOL(ume) ^ button. The tuner scans and memorizes all active channels in your area. . The TV distinguishes between standard TV channels and cable (CATV) channels. . When AUTO PRESET CH action is completed, the lowest memorized channel reappears on the screen. . When you press the CH(annel) Ў or ^ button after selecting "AUTO PRESET CH", the tuner will stop at the memorized channels only. . The TV may recognize TV channels to be CATV channels by receiving conditions. In this case, try AUTO PRESET CH action again in the fine receiving conditions. . When AUTO PRESET CH is activated where there is no TV signal input, "NO TV SIGNALS" will appear on the display after the completion of channel scanning. [ADD/DELETE FUNCTION] 1) Press the MENU button so that the menu display appears on the TV screen. 2) Press the CH(annel) Ў or ^ button to point to "CHANNEL SET". Then, press the VOL(ume) ^ button. sleep time will be lost. You may view specially labeled (cc) TV programs, movies, news, prerecorded tapes, etc. with either a dialogue caption or text display added to the program. : Press the VOL(ume) Ў or ^ button. PICTURE CHANNEL SET [ENG] / ESP / FRA V-CHIP SET UP CAPTION [OFF] TV SOUND [MAIN] PICTURE CHANNEL SET [ENG] / ESP / FRA V-CHIP SET UP CAPTION [OFF] TV SOUND [MAIN] OPERATIONS 1) Press the POWER button to turn on the TV. 2) Select the desired channel with the CH(annel) Ў or ^ button. 3) Adjust the volume to the desired listening level using the VOL(ume) Ў or ^ button. 4) Adjust picture controls for a natural looking image. (See PICTURE ADJUSTMENT.) The sleep timer function allows you to have the power automatically turn off after a set time period. 1) Press the POWER button to turn on the TV and press the SLEEP button on the remote control . 2) You may...